Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0418857 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  B1273  Sliding Roof ECU Communication Stop  B2321  D-Door Motor ECU Communication Stop  B2322  P-Door Motor ECU Communication Stop  B2323  RR-Door Motor ECU Communication Stop  B2324  RL-Door Motor ECU Communication Stop  B2329  Lost Communication with Sliding Sunshade ECU  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, power window regulator motor assembly (driver door), power window regulator motor assembly (front passenger door), power window regulator motor assembly (rear RH door), power window regulator motor assembly (rear LH door), sliding roof ECU (sliding roof drive gear assembly)*1*2 or roof sunshade ECU (sliding roof drive gear assembly)*2 stops for 10 seconds or more.

*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System


DTC No. Detection Item DTC Detection Condition Trouble Area
B1206 P/W Master Switch Communication Stop No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Wire harness or connector

·

ECU-B NO. 2 fuse


B1273 Sliding Roof ECU Communication Stop No communication between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.*1*2
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Sliding roof ECU (sliding roof drive gear assembly)

·

Wire harness or connector

·

S/ROOF fuse


B2321 D-Door Motor ECU Communication Stop No communication between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Power window regulator motor assembly (driver door)

·

Wire harness or connector

·

DOOR F/L fuse


B2322 P-Door Motor ECU Communication Stop No communication between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Power window regulator motor assembly (front passenger door)

·

Wire harness or connector

·

DOOR F/R fuse


B2323 RR-Door Motor ECU Communication Stop No communication between power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Power window regulator motor assembly (rear RH door)

·

Wire harness or connector

·

DOOR R/R fuse


B2324 RL-Door Motor ECU Communication Stop No communication between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Power window regulator motor assembly (rear LH door)

·

Wire harness or connector

·

DOOR R/L fuse


B2329 Lost Communication with Sliding Sunshade ECU No communication between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.*2
·

Roof sunshade ECU (sliding roof drive gear assembly)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

SHADE fuse



*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System


WIRING DIAGRAM

B605726E01
4.313,0.271 5.792,0.698 1.479,0.427 10 false from Auxiliary Battery 4.708,0.979 5.021,1.177 0.313,0.198 10 false 17 4.698,1.313 5.01,1.51 0.313,0.198 10 false 16 6,1.01 6.313,1.208 0.313,0.198 10 false 11 6.01,1.417 6.323,1.615 0.313,0.198 10 false 12 6.073,1.24 6.938,1.677 0.865,0.438 10 false ECU-B NO. 2 4.948,1.125 5.563,1.323 0.615,0.198 10 false LIN1 4.948,1.438 5.563,1.635 0.615,0.198 10 false LIN2 5.833,1.135 6.031,1.417 0.198,0.281 10 false B 5.646,1.479 6.26,1.677 0.615,0.198 10 false GND 4.885,1.802 5.5,2 0.615,0.198 10 false J18 4.875,1.948 6.479,2.385 1.604,0.438 10 false Multiplex Network Master Switch Assembly 6.115,2.854 7.094,3.333 0.979,0.479 10 false DOOR F/L*1 6.01,2.646 6.323,2.844 0.313,0.198 10 false 2 6.01,3 6.323,3.198 0.313,0.198 10 false 1 5.844,2.74 6.042,3.021 0.198,0.281 10 false B 5.646,3.083 6.26,3.281 0.615,0.198 10 false GND 4.948,2.927 5.563,3.125 0.615,0.198 10 false LIN 4.771,2.76 5.083,2.958 0.313,0.198 10 false 9 4.146,3.302 5.375,3.5 1.229,0.198 10 false J24*1, J8*2 4.146,3.469 6.729,3.948 2.583,0.479 10 false Power Window Regulator Motor Assembly (Driver Door) 6.125,4.521 6.948,4.969 0.823,0.448 10 false DOOR F/R*1 6,4.281 6.313,4.479 0.313,0.198 10 false 2 6,4.656 6.313,4.854 0.313,0.198 10 false 1 5.844,4.406 6.042,4.688 0.198,0.281 10 false B 5.656,4.75 6.271,4.948 0.615,0.198 10 false GND 4.938,4.573 5.552,4.771 0.615,0.198 10 false LIN 4.781,4.406 5.094,4.604 0.313,0.198 10 false 9 4.177,4.99 5.385,5.271 1.208,0.281 10 false J8*1, J24*2 4.156,5.167 6.74,5.646 2.583,0.479 10 false Power Window Regulator Motor Assembly (Front Passenger Door) 0.083,6.427 0.396,6.625 0.313,0.198 10 false A 3.719,5.625 4.031,5.823 0.313,0.198 10 false B 6.875,5.625 7.094,5.938 0.219,0.313 10 false C 2.979,0.958 3.292,1.156 0.313,0.198 10 false 17 1.688,0.958 2,1.156 0.313,0.198 10 false 16 1.656,1.156 1.99,1.458 0.333,0.302 10 false MB 2.979,1.156 3.313,1.458 0.333,0.302 10 false 4B 2.979,1.76 3.313,2.063 0.333,0.302 10 false 4D 3,1.552 3.313,1.75 0.313,0.198 10 false 25 1.219,1.135 1.833,1.333 0.615,0.198 10 false LIN2 0.469,2.406 1.615,2.979 1.146,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 1.781,2.219 2.854,2.969 1.073,0.75 10 false Instrument Panel Junction Block Assembly 2.198,4.427 2.51,4.625 0.313,0.198 10 false 9 1.896,4.573 2.51,4.771 0.615,0.198 10 false LIN 1.125,4.385 1.323,4.667 0.198,0.281 10 false B 1.115,4.771 1.729,4.969 0.615,0.198 10 false GND 0.958,4.302 1.271,4.5 0.313,0.198 10 false 2 0.958,4.677 1.271,4.875 0.313,0.198 10 false 1 0.26,4.552 1.01,5.01 0.75,0.458 10 false DOOR R/L 0.76,5.01 1.375,5.208 0.615,0.198 10 false K9 0.75,5.177 3.333,5.656 2.583,0.479 10 false Power Window Regulator Motor Assembly (Rear LH Door) 2.198,6.063 2.51,6.26 0.313,0.198 10 false 9 1.917,6.219 2.531,6.417 0.615,0.198 10 false LIN 1.115,6.063 1.313,6.344 0.198,0.281 10 false B 1.115,6.406 1.729,6.604 0.615,0.198 10 false GND 0.958,5.938 1.271,6.135 0.313,0.198 10 false 2 0.948,6.292 1.26,6.49 0.313,0.198 10 false 1 0.271,6.198 1.021,6.656 0.75,0.458 10 false DOOR R/R 0.74,6.708 1.354,6.906 0.615,0.198 10 false K4 0.74,6.865 3.323,7.344 2.583,0.479 10 false Power Window Regulator Motor Assembly (Rear RH Door) 0.667,7.469 4.333,7.667 3.667,0.198 10 false : LIN Communication Line 6.104,3.031 6.969,3.354 0.865,0.323 10 false DOOR F/R*2 6.125,4.698 6.927,4.917 0.802,0.219 10 false DOOR F/L*2 4.833,6.583 6.521,6.781 1.688,0.198 10 false *1: for LHD 4.833,6.979 6.521,7.177 1.688,0.198 10 false *2: for RHD

B566993E02
0.698,5.375 4.365,5.573 3.667,0.198 10 false : LIN Communication Line 3.167,5.042 7.146,5.24 3.979,0.198 10 false *1: w/ Sliding Roof System 3.167,5.365 7.146,5.563 3.979,0.198 10 false *2: w/ Panoramic Moon Roof System 4.479,3.438 5.094,3.635 0.615,0.198 10 false MPX1 5.51,3.229 5.667,3.427 0.156,0.198 10 false B 5.521,3.583 5.677,3.781 0.156,0.198 10 false E 6.01,3.396 6.698,3.615 0.688,0.219 10 false SHADE*2 6,1.385 6.74,1.604 0.74,0.219 10 false S/ROOF*2 5.521,1.219 5.677,1.417 0.156,0.198 10 false B 5.521,1.594 5.677,1.792 0.156,0.198 10 false E 4.5,1.406 5.115,1.604 0.615,0.198 10 false MPX1 2.26,1.406 2.875,1.604 0.615,0.198 10 false MPX1 1.479,1.198 1.635,1.396 0.156,0.198 10 false B 1.479,1.573 1.635,1.771 0.156,0.198 10 false E 3.5,0.417 3.656,0.615 0.156,0.198 10 false B 0.167,0.417 0.323,0.615 0.156,0.198 10 false A 6.823,0.427 6.979,0.625 0.156,0.198 10 false C 0.521,1.365 1.26,1.583 0.74,0.219 10 false S/ROOF*1 1.135,2.063 3.052,2.854 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*1 4.208,2.052 6.125,2.844 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*2 4.177,4.042 5.979,4.906 1.802,0.865 10 false Roof Sunshade ECU (Sliding Roof Drive Gear Assembly)*2 5.698,1.125 5.854,1.323 0.156,0.198 10 false 8 5.688,1.49 5.958,1.719 0.271,0.229 10 false 12 4.24,1.26 4.51,1.49 0.271,0.229 10 false 11 4.219,1.896 4.573,2.146 0.354,0.25 10 false R19 5.708,3.135 5.865,3.333 0.156,0.198 10 false 8 5.708,3.49 5.979,3.719 0.271,0.229 10 false 12 4.25,3.292 4.521,3.521 0.271,0.229 10 false 11 4.177,3.885 4.531,4.135 0.354,0.25 10 false R20 2.719,1.271 2.875,1.469 0.156,0.198 10 false 7 1.302,1.094 1.458,1.292 0.156,0.198 10 false 1 1.302,1.458 1.458,1.656 0.156,0.198 10 false 2 1.146,1.896 1.5,2.146 0.354,0.25 10 false R2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*

w/ Sliding Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

w/ Panoramic Moon Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

*: w/ Sliding Roof System or Panoramic Moon Roof System


·

When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

*: w/ Panoramic Moon Roof System


·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC is not output A
DTC B1206, B1273*1*2, B2321, B2322, B2323, B2324 and B2329*2 are output B
DTC B1206, B1273*1*2, B2321, B2322 and B2329*2 are output C
DTC B2323 and B2324 are output D
Only DTC B1206 and B2321 are output E
Only DTC B1206 is output F
Only DTC B1273 is output*1*2 G
Only DTC B2321 is output H
Only DTC B2322 is output I
Only DTC B2323 is output J
Only DTC B2324 is output K
Only DTC B1273 and B2329 are output*2 L
Only DTC B2329 is output*2 M


*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System



A

B

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

E

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

F

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

G

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

H

12.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

I

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))

J

17.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))

K

19.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

L

21.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

M

22.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B567934C01
1.875,1.25 2.292,1.552 0.417,0.302 5.479,0.344 5.896,0.646 0.417,0.302 5.51,2.188 5.927,2.49 0.417,0.302 2.208,2.438 2.01,2.438 2.01,2.438 2.01,1.906 true 1.979,1.323 2.292,1.521 0.313,0.198 10 false MB 5.594,0.406 5.906,0.604 0.313,0.198 10 false 4B 5.625,2.25 5.938,2.448 0.313,0.198 10 false 4D 2.26,2.344 2.875,2.542 0.615,0.198 10 false LIN2 0.26,0.156 0.604,0.375 0.344,0.219 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
MB-16 (LIN2) - 4B-17 or 4D-25 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B567935C01
1.875,0.333 2.292,0.583 0.417,0.25 5.594,0.24 6.01,0.49 0.417,0.25 2.344,1.396 2.156,1.396 2.156,1.396 2.156,0.927 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.979,0.375 2.292,0.531 0.313,0.156 10 false MB 5.698,0.271 6.01,0.427 0.313,0.156 10 false 4B 2.385,1.302 2.802,1.479 0.417,0.177 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
MB-16 (LIN2) - 4B-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the J18 multiplex network master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 - J18-17 (LIN1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B567936C01
1.875,0.333 2.292,0.583 0.417,0.25 5.563,0.281 5.979,0.531 0.417,0.25 2.344,1.396 2.156,1.396 2.156,1.396 2.156,0.927 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.979,0.375 2.292,0.531 0.313,0.156 10 false MB 5.688,0.323 6,0.479 0.313,0.156 10 false 4D 2.385,1.302 2.802,1.479 0.417,0.177 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
MB-16 (LIN2) - 4D-25 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))
a.

Disconnect the K9 power window regulator motor assembly (rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - K9-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Disconnect the J18 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 - J18-17 (LIN1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J18-11 (B) - J18-12 (GND) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J18-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Disconnect the R2*1 or R19*2 sliding roof ECU (sliding roof drive gear assembly) connector.

*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof System
Tester Connection Condition Specified Condition
4B-17 - R2-7 (MPX1) Ignition switch off Below 1 Ω

w/ Panoramic Moon Roof System
Tester Connection Condition Specified Condition
4B-17 - R19-11 (MPX1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Sliding Roof System
Tester Connection Condition Specified Condition
R2-1 (B) - R2-2 (E) Ignition switch off*1
Always*2
11 to 14 V

w/ Panoramic Moon Roof System
Tester Connection Condition Specified Condition
R19-8 (B) - R19-12 (E) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof System
Tester Connection Condition Specified Condition
R2-2 (E) - Body ground Always Below 1 Ω

w/ Panoramic Moon Roof System
Tester Connection Condition Specified Condition
R19-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B365181C14
0.24,0.135 0.552,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Multiplex Network Master Switch Assembly)


Remove the multiplex network master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 - 17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the J24*1 or J8*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J18-16 (LIN2) - J24-9 (LIN) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J18-16 (LIN2) - J8-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
J24-2 (B) - J24-1 (GND) Ignition switch off*1
Always*2
11 to 14 V

for RHD
Tester Connection Condition Specified Condition
J8-2 (B) - J8-1 (GND) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J24-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J8-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Disconnect the J8*1 or J24*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
4B-17 - J8-9 (LIN) Ignition switch off Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
4B-17 - J24-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
J8-2 (B) - J8-1 (GND) Ignition switch off*1
Always*2
11 to 14 V

for RHD
Tester Connection Condition Specified Condition
J24-2 (B) - J24-1 (GND) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J8-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J24-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Disconnect the K4 power window regulator motor assembly (rear RH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - K4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K4-2 (B) - K4-1 (GND) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Disconnect the K9 power window regulator motor assembly (rear LH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - K9-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K9-2 (B) - K9-1 (GND) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K9-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Disconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 - R19-11 (MPX1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Disconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 - R20-11 (MPX1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R20-8 (B) - R20-12 (E) Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR