Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

C428886E02
0.406,1.875 2.094,2.469 1.688,0.594 10 false No. 2 Global CAN Junction Connector 0.063,1.875 0.521,2.073 0.458,0.198 10 false H90 1.604,0.844 2.063,1.042 0.458,0.198 10 false 3 1.573,1.385 2.031,1.583 0.458,0.198 10 false 13 5.427,0.854 5.885,1.052 0.458,0.198 10 false 27 5.438,1.354 5.896,1.552 0.458,0.198 10 false 43 5.438,1.885 5.896,2.083 0.458,0.198 10 false 46 5.448,2.479 5.906,2.677 0.458,0.198 10 false 14 5.448,3.042 5.906,3.24 0.458,0.198 10 false 45 5.458,4.031 5.917,4.229 0.458,0.198 10 false 1 5.719,4.115 6.177,4.313 0.458,0.198 10 false GND1 5.719,3.135 6.177,3.333 0.458,0.198 10 false IG1 5.708,0.948 6.167,1.146 0.458,0.198 10 false CANH 5.708,1.479 6.167,1.677 0.458,0.198 10 false CANL 3.969,2.979 5.719,3.302 1.75,0.323 10 false ECU-IG1 NO. 2 1.656,3.125 3.135,3.573 1.479,0.448 10 false from IG1-NO.1 Relay*2 4.063,1.813 5.813,2.135 1.75,0.323 10 false ABS NO. 1 4.083,2.396 5.833,2.719 1.75,0.323 10 false ABS NO. 2 2.333,1.969 3.875,2.292 1.542,0.323 10 false from Battery 2.333,2.552 3.875,2.875 1.542,0.323 10 false from Battery 5.448,4.906 7.115,5.344 1.667,0.438 10 false Brake Actuator Assembly 5.094,4.917 5.542,5.156 0.448,0.24 10 false A39 5.719,1.958 6.177,2.156 0.458,0.198 10 false BM 5.698,2.542 6.156,2.74 0.458,0.198 10 false +BS 5.427,4.417 5.885,4.615 0.458,0.198 10 false 30 0.99,3.75 3.375,4.177 2.385,0.427 10 false from Engine Stop and Start ECU*1 5.729,4.51 6.188,4.708 0.458,0.198 10 false GND2 0.25,4.781 2.198,5.115 1.948,0.333 10 false *1 w/ Stop and Start System 0.25,5.135 2.198,5.469 1.948,0.333 10 false *2 w/o Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A39 brake actuator assembly connector.


c.
C427100C01
1.458,0.115 1.927,0.333 0.469,0.219 2.083,1.25 2.083,0.5 2.083,0.5 2.333,0.5 true 2.333,1.938 2.083,1.938 2.083,1.938 2.083,1.354 true 1.552,0.146 2.01,0.344 0.458,0.198 10 false A39 2.406,0.427 3.021,0.625 0.615,0.198 10 false CANH 2.375,1.854 2.99,2.052 0.615,0.198 10 false CANL 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-27 (CANH) - A39-43 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C427100C02
1.458,0.115 1.927,0.333 0.469,0.219 0.833,1.052 0.833,0.51 0.833,0.51 0.656,0.51 true 1.083,1.948 0.833,1.948 0.833,1.948 0.833,1.365 true 1.552,0.146 2.01,0.344 0.458,0.198 10 false A39 0.229,0.438 0.844,0.635 0.615,0.198 10 false GND1 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 1.125,1.875 1.74,2.073 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A39-30 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

3.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.
C427100C03
1.458,0.115 1.927,0.333 0.469,0.219 2.469,1.052 2.469,0.51 2.469,0.51 2.625,0.51 true 2.073,1.958 2.26,1.958 2.26,1.958 2.26,1.375 true 2.719,1.948 2.469,1.948 2.469,1.948 2.469,1.365 true 1.552,0.146 2.01,0.344 0.458,0.198 10 false A39 2.677,0.417 3.292,0.615 0.615,0.198 10 false +BS 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 1.781,1.885 2.396,2.083 0.615,0.198 10 false IG1 2.781,1.875 3.396,2.073 0.615,0.198 10 false BM
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
A39-46 (BM) - Body ground Always 11 to 14 V
A39-14 (+BS) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

NG

GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.
C427100C03
1.458,0.115 1.927,0.333 0.469,0.219 2.469,1.052 2.469,0.51 2.469,0.51 2.625,0.51 true 2.073,1.958 2.26,1.958 2.26,1.958 2.26,1.375 true 2.719,1.948 2.469,1.948 2.469,1.948 2.469,1.365 true 1.552,0.146 2.01,0.344 0.458,0.198 10 false A39 2.677,0.417 3.292,0.615 0.615,0.198 10 false +BS 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 1.781,1.885 2.396,2.083 0.615,0.198 10 false IG1 2.781,1.875 3.396,2.073 0.615,0.198 10 false BM
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 11 to 14 V
A39-46 (BM) - Body ground Always 11 to 14 V
A39-14 (+BS) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)