Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Main body ECU (multiplex network body ECU) branch line or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly



WIRING DIAGRAM

C448226E01
0.49,1.531 2.854,1.969 2.365,0.438 10 false No. 4 Global CAN Junction Connector 0.135,1.531 0.542,1.802 0.406,0.271 10 false H92 1.75,0.375 1.969,0.615 0.219,0.24 10 false 1 1.76,1.021 1.979,1.26 0.219,0.24 10 false 7 5.573,0.49 5.979,0.76 0.406,0.271 10 false H43 5.573,1.156 5.979,1.427 0.406,0.271 10 false H43 6,0.479 6.573,0.781 0.573,0.302 10 false CANH 5.99,1.146 6.563,1.448 0.573,0.302 10 false CANL 5.667,0.271 5.885,0.51 0.219,0.24 10 false 5 5.656,0.938 5.875,1.177 0.219,0.24 10 false 4 6,2.427 6.5,2.781 0.5,0.354 10 false BECU 5.594,2.427 6,2.698 0.406,0.271 10 false MB 5.625,2.188 5.927,2.49 0.302,0.302 10 false 31 2.958,2.406 3.365,2.677 0.406,0.271 10 false 4B 2.969,2.177 3.375,2.448 0.406,0.271 10 false 23 1.302,3.573 2.979,3.969 1.677,0.396 10 false from Battery 2.958,3.604 3.365,3.875 0.406,0.271 10 false 4F 3,3.365 3.219,3.604 0.219,0.24 10 false 1 3.781,4.604 4.229,4.917 0.448,0.313 10 false ACC 4.635,3.917 5.625,4.271 0.99,0.354 10 false ECU-ACC 5.594,4.042 6,4.313 0.406,0.271 10 false MB 5.615,3.813 5.917,4.115 0.302,0.302 10 false 30 6,4.031 6.5,4.385 0.5,0.354 10 false ACC 2.969,4.104 3.271,4.406 0.302,0.302 10 false 30 2.958,4.323 3.365,4.594 0.406,0.271 10 false 4A 0.26,4.302 2.125,4.802 1.865,0.5 10 false from Certification ECU (Smart Key ECU Assembly) 5.583,5.406 5.99,5.677 0.406,0.271 10 false MB 5.625,5.156 5.927,5.458 0.302,0.302 10 false 32 5.99,5.396 6.49,5.75 0.5,0.354 10 false IG 4.542,5.26 6.031,5.615 1.49,0.354 10 false ECU-IG1 NO. 4 3.656,5.948 4.635,6.344 0.979,0.396 10 false IG1-NO. 1 2.948,5.667 3.354,5.938 0.406,0.271 10 false 4A 2.958,5.427 3.26,5.729 0.302,0.302 10 false 17 0.25,5.667 2.115,6.167 1.865,0.5 10 false from Certification ECU (Smart Key ECU Assembly) 2.948,6.479 3.26,6.76 0.313,0.281 10 false 4B 3.01,6.25 3.313,6.552 0.302,0.302 10 false 3 5.594,6.479 6,6.75 0.406,0.271 10 false MB 5.625,6.25 5.927,6.552 0.302,0.302 10 false 11 6.01,6.49 6.594,6.771 0.583,0.281 10 false GND1 2.813,7.542 4.438,7.99 1.625,0.448 10 false Instrument Panel Junction Block Assembly 5.458,7.531 7.156,8.135 1.698,0.604 10 false Main Body ECU (Multiplex Network Body ECU) 0.406,2.385 2.229,2.854 1.823,0.469 10 false from Door Control Battery*1 1.188,2.99 2.865,3.385 1.677,0.396 10 false from Battery*2 0.135,7.927 2.083,8.292 1.948,0.365 10 false *1: w/ Door Control Battery 0.135,8.292 2.083,8.656 1.948,0.365 10 false *2: w/o Door Control Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing troubleshooting, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


c.
C369119C32
1.583,0.167 2,0.417 0.417,0.25 2.375,0.865 2.542,0.865 2.542,0.865 2.542,1.531 true 2.531,0.688 2.698,0.688 2.698,0.688 2.698,1.521 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.667,0.198 1.979,0.396 0.313,0.198 10 false H43 2.094,0.615 2.573,0.823 0.479,0.208 10 false CANH 1.958,0.792 2.438,1 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-5 (CANH) - H43-4 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.
C227508C75
1.531,0.552 1.917,0.792 0.385,0.24 1.219,1.083 1.135,0.771 1.135,0.771 1.021,0.771 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.615,0.583 1.927,0.74 0.313,0.156 10 false MB 0.552,0.698 0.99,0.875 0.438,0.177 10 false GND1
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-11 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)

NG

8.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.
C227508C76
1.531,0.552 1.917,0.792 0.385,0.24 3,1.073 2.76,0.438 2.76,0.438 2.646,0.438 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.615,0.583 1.927,0.74 0.313,0.156 10 false MB 2.188,0.375 2.625,0.552 0.438,0.177 10 false BECU
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MB-31 (BECU) - Body ground Always 11 to 14 V


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ACC SIGNAL CIRCUIT)

NG

6.CHECK VEHICLE TYPE
4.CHECK HARNESS AND CONNECTOR (ACC SIGNAL CIRCUIT)
a.
C227508C77
1.531,0.552 1.917,0.792 0.385,0.24 2.917,1.073 2.677,0.438 2.677,0.438 2.563,0.438 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.615,0.583 1.927,0.74 0.313,0.156 10 false MB 2.229,0.365 2.667,0.542 0.438,0.177 10 false ACC
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MB-30 (ACC) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG SIGNAL CIRCUIT)

NG

GO TO LIGHTING (INT) SYSTEM (ACC SIGNAL CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (IG SIGNAL CIRCUIT)
a.
C227508C78
1.531,0.552 1.917,0.792 0.385,0.24 3.094,1.073 2.854,0.438 2.854,0.438 2.74,0.438 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.615,0.583 1.927,0.74 0.313,0.156 10 false MB 2.563,0.354 3,0.531 0.438,0.177 10 false IG
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MB-32 (IG) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING (INT) SYSTEM (IG SIGNAL CIRCUIT)

6.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Door Control Battery A
w/ Door Control Battery B



A

7.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)

B

GO TO POWER DOOR LOCK CONTROL SYSTEM (BECU SIGNAL CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4B instrument panel junction block assembly connector.


c.

Reconnect the cable to the negative (-) battery terminal.


d.
C352870C29
1.458,0.135 1.781,0.365 0.323,0.229 0.927,1.333 0.927,1.844 0.927,1.844 1.073,1.844 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.531,0.167 1.844,0.365 0.313,0.198 10 false 4B 1.167,1.729 1.719,1.969 0.552,0.24 10 false 4B-23
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-23 - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4B instrument panel junction block assembly connector.


c.
C352871C63
1.177,0.146 1.51,0.385 0.333,0.24 1.75,0.896 1.75,0.313 1.75,0.313 1.896,0.313 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.969,0.229 2.5,0.49 0.531,0.26 10 false 4B-3 1.271,0.188 1.583,0.385 0.313,0.198 10 false 4B
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-3 - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)