Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Operated Using Kick Sensor  


DESCRIPTION

The kick door control sensor turns the sensing circuit on or off based on the vehicle speed and IG and ACC signals sent from the main body ECU (multiplex network body ECU) via LIN communication.

When the kick door control sensor detects a kick operation, it sends an operation signal to the multiplex network door ECU.

WIRING DIAGRAM

B526715E08
0.521,3.76 2.74,3.958 2.219,0.198 10 false : CAN Communication Line 0.542,4.208 3.125,4.531 2.583,0.323 10 false : LIN Communication Line 2.156,2.896 3.26,3.177 1.104,0.281 10 false V7 2.156,3.063 3.25,3.417 1.094,0.354 10 false Kick Door Control Sensor 5.5,3.688 7.146,4.188 1.646,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.5,3.531 5.958,3.729 0.458,0.198 10 false MB 2.74,0.573 3.354,0.771 0.615,0.198 10 false KSOT 3.802,1.219 4.917,1.563 1.115,0.344 10 false Multiplex Network Door ECU 3.802,1.063 4.26,1.26 0.458,0.198 10 false W18 5.552,1.094 7.083,1.479 1.531,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.375,0.573 2.531,0.771 0.156,0.198 10 false B 4.052,0.583 4.667,0.781 0.615,0.198 10 false KSIN 2.365,2.406 2.979,2.604 0.615,0.198 10 false GND 2.896,2.385 3.51,2.583 0.615,0.198 10 false LIN 2.156,2.271 2.313,2.469 0.156,0.198 10 false 7 3.24,0.448 3.396,0.646 0.156,0.198 10 false 3 2.135,0.448 2.292,0.646 0.156,0.198 10 false 2 3.219,2.208 3.375,2.406 0.156,0.198 10 false 6 1.344,0.719 3.177,0.917 1.833,0.198 10 false ECU-B NO. 2 0.26,0.552 1.135,1.115 0.875,0.563 10 false from Auxiliary Battery 5.917,2.396 6.531,2.594 0.615,0.198 10 false LIN2 3.833,2.927 4.292,3.125 0.458,0.198 10 false 4B 3.833,3.104 5.448,3.5 1.615,0.396 10 false Instrument Panel Junction Block Assembly 3.802,0.438 4.115,0.635 0.313,0.198 10 false 14 5.594,2.198 5.906,2.396 0.313,0.198 10 false 16 4.135,2.198 4.448,2.396 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the "Kick Sensor Function" customize setting is set to "ON" (The default is "ON").

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS

·

The power back door system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power back door system after confirming that the CAN communication system is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

The power back door system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power back door system after confirming that the LIN communication system is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Check the entry and start system (for Entry Function) first before troubleshooting the power back door system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before troubleshooting, be sure to read Precautions for Hands Free Power Back Door.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>PRECAUTION

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

After performing work, using the GTS, read the Data List item "Kick Sensor Connection" and check that the kick door control sensor is connected.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Kick Sensor Error Status of the kick door control sensor error Normal or Error Normal: Kick door control sensor is normal
Error: Kick door control sensor is abnormal
-
Body Electrical > Back Door > Data List
Tester Display
Kick Sensor Error
50003 159 77
OK:

On the display, Normal is displayed.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE KICK DOOR CONTROL SENSOR

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Kick Sensor Detection Status of the kick door control sensor detection OFF or ON OFF: Kick door control sensor not detecting a foot
ON: Kick door control sensor detecting a foot
-
Body Electrical > Back Door > Data List
Tester Display
Kick Sensor Detection
50003 159 76
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - AUXILIARY BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the V7 kick door control sensor connector.


b.

Disconnect the 4B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-6 (LIN) - 4B-17 Always Below 1 Ω
V7-6 (LIN) or 4B-17 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE KICK DOOR CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - AUXILIARY BATTERY AND BODY GROUND)
a.
E409579C09
0.635,1.094 1.042,1.354 0.406,0.26 0.75,1.135 1.063,1.333 0.313,0.198 10 false V7 0.135,0.167 0.448,0.365 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Kick Door Control Sensor)


Disconnect the V7 kick door control sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V7-2 (B) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - MULTIPLEX NETWORK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the W18 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-3 (KSOT) - W18-14 (KSIN) Always Below 1 Ω
V7-3 (KSOT) or W18-14 (KSIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MULTIPLEX NETWORK DOOR ECU
a.

Remove the multiplex network door ECU with the connector(s) still connected.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL


b.
B556215C03
1.521,0.281 1.938,0.521 0.417,0.24 0.938,1.688 1.396,1.177 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.583,0.313 2.042,0.51 0.458,0.198 10 false W18 0.75,1.729 1.208,1.927 0.458,0.198 10 false KSIN 0.146,4.083 0.604,4.281 0.458,0.198 10 false GND 0.365,2.698 0.677,2.896 0.313,0.198 10 false *b
*a Component with harness connected
(Multiplex Network Door ECU)
*b Waveform


Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection W18-14 (KSIN) - Body ground
Tool Setting 2 V/DIV., 50 ms/DIV.
Vehicle Condition Kick door control sensor not detecting a foot

OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE KICK DOOR CONTROL SENSOR

NG

REPLACE MULTIPLEX NETWORK DOOR ECU