Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › from 2020.11
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420033 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (driver door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (driver door) operates the vertical and horizontal mirror motors, which are built into the outer mirror actuator assembly (driver door), to adjust the mirror surface position.

WIRING DIAGRAM

B581836E06
1.031,0.667 1.583,0.906 0.552,0.24 10 false M+ 0.896,1.656 1.448,1.896 0.552,0.24 10 false MSW 1.156,2.635 1.708,2.875 0.552,0.24 10 false E 2.042,2.635 2.594,2.875 0.552,0.24 10 false MIRE 2.042,1.656 2.594,1.896 0.552,0.24 10 false MIRS 2.042,0.677 2.594,0.917 0.552,0.24 10 false MIRB 1.385,0.573 1.771,0.833 0.385,0.26 10 false 4 1.823,0.583 2.208,0.844 0.385,0.26 10 false 7 1.813,1.469 2.198,1.729 0.385,0.26 10 false 8 1.385,1.469 1.771,1.729 0.385,0.26 10 false 5 1.802,2.49 2.188,2.75 0.385,0.26 10 false 9 0.167,3.333 0.552,3.594 0.385,0.26 10 false J22 0.552,4.365 2.302,4.625 1.75,0.26 10 false : CAN Communication Line 0.156,3.5 1.365,3.875 1.208,0.375 10 false Outer Mirror Switch Assembly 1.833,3.323 2.219,3.583 0.385,0.26 10 false H44 1.854,3.479 3,4.198 1.146,0.719 10 false Main Body ECU (Multiplex Network Body ECU) 3.396,3.344 4.396,3.594 1,0.25 10 false z17*1, z16*2 3.385,3.51 4.927,3.948 1.542,0.438 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.354,3.406 6.802,3.917 1.448,0.51 10 false Outer Rear View Mirror Assembly (Driver Door) 5.375,0.75 6.865,1.021 1.49,0.271 10 false Horizontal Mirror Motor 5.427,1.938 6.833,2.198 1.406,0.26 10 false Vertical Mirror Motor 4.635,0.542 5.125,0.813 0.49,0.271 10 false MH 4.677,1.156 5.167,1.427 0.49,0.271 10 false M+ 4.646,1.719 5.135,1.99 0.49,0.271 10 false MV 1.406,2.49 1.792,2.75 0.385,0.26 10 false 7 5.021,0.438 5.51,0.708 0.49,0.271 10 false 9 4.99,1.031 5.479,1.302 0.49,0.271 10 false 10 5.01,1.635 5.5,1.906 0.49,0.271 10 false 1 4.99,2.542 6.958,2.948 1.969,0.406 10 false Outer Mirror Actuator Assembly (Driver Door) 5.198,0.438 5.688,0.708 0.49,0.271 10 false 3 5.208,1.031 5.698,1.302 0.49,0.271 10 false 4 5.198,1.635 5.688,1.906 0.49,0.271 10 false 1 5.01,2.375 5.5,2.646 0.49,0.271 10 false B 3.344,4.396 4.344,4.646 1,0.25 10 false *1: for LHD 4.635,4.417 5.635,4.667 1,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch R switch on
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch off
ON: Mirror select switch L switch on
-
Mirror Position SW (R) Mirror adjust switch signal (Right) OFF or ON OFF: Mirror adjust switch not pushed right
ON: Mirror adjust switch pushed right
Check with the mirror select switch L or R selected
Mirror Position SW (L) Mirror adjust switch signal (Left) OFF or ON OFF: Mirror adjust switch not pushed left
ON: Mirror adjust switch pushed left
Check with the mirror select switch L or R selected
Mirror Position SW (Up) Mirror adjust switch signal (Up) OFF or ON OFF: Mirror adjust switch not pushed up
ON: Mirror adjust switch pushed up
Check with the mirror select switch L or R selected
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) OFF or ON OFF: Mirror adjust switch not pushed down
ON: Mirror adjust switch pushed down
Check with the mirror select switch L or R selected
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (MIRROR SURFACE)

NG

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (MIRROR SURFACE)

OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (WIRE HARNESS)
3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (WIRE HARNESS)
a.

Remove the outer mirror actuator assembly (driver door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Disconnect the z17*1 or z16*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



c.
B559030C22
0.063,1.708 0.438,1.906 0.375,0.198 0.063,0.542 0.438,0.74 0.375,0.198 0.073,0.792 0.448,0.99 0.375,0.198 0.979,0.135 1.188,0.135 1.188,0.135 1.188,0.708 true 1.521,1.24 1.333,1.24 1.333,1.24 1.333,0.99 true 1.188,1 1.188,1.24 1.188,1.24 1.021,1.24 true 0.219,1.74 0.438,1.906 0.219,0.167 10 false B 0.51,0.573 0.844,0.74 0.333,0.167 10 false *A 0.25,0.135 0.563,0.333 0.313,0.198 10 false *a 0.271,1.323 0.583,1.521 0.313,0.198 10 false *b 0.708,0.063 1.042,0.229 0.333,0.167 10 false MV 1.583,1.156 1.917,1.323 0.333,0.167 10 false M+ 0.781,1.167 1.115,1.333 0.333,0.167 10 false MH 0.156,0.563 0.49,0.729 0.333,0.167 10 false z17 0.156,0.813 0.49,0.979 0.333,0.167 10 false z16 0.521,0.813 0.854,0.979 0.333,0.167 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector (to Outer Mirror Control ECU Assembly (Driver Door))
*b Front view of wire harness connector (to Outer Mirror Actuator Assembly (Driver Door))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
z17-9 (MH) - B-3 Always Below 1 Ω
z17-9 (MH) or B-3 - Body ground Always 10 kΩ or higher
z17-10 (M+) - B-4 Always Below 1 Ω
z17-10 (M+) or B-4 - Body ground Always 10 kΩ or higher
z17-1 (MV) - B-1 Always Below 1 Ω
z17-1 (MV) or B-1 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
z16-9 (MH) - B-3 Always Below 1 Ω
z16-9 (MH) or B-3 - Body ground Always 10 kΩ or higher
z16-10 (M+) - B-4 Always Below 1 Ω
z16-10 (M+) or B-4 - Body ground Always 10 kΩ or higher
z16-1 (MV) - B-1 Always Below 1 Ω
z16-1 (MV) or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H44 main body ECU (multiplex network body ECU).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J22-7 (E) - H44-9 (MIRE) Always Below 1 Ω
J22-4 (M+) - H44-7 (MIRB) Always Below 1 Ω
J22-5 (MSW) - H44-8 (MIRS) Always Below 1 Ω
J22-7 (E) or H44-9 (MIRE) - Body ground Always 10 kΩ or higher
J22-4 (M+) or H44-7 (MIRB) - Body ground Always 10 kΩ or higher
J22-5 (MSW) or H44-8 (MIRS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR