Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C136F00  Non-learning of the Braking System information.  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRC, etc.) based on the identification information.

NOTICE:

DTC C136F00 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C136F00 Non-learning of the Braking System information. Either of the following is detected:
·

The drive system information sent from the hybrid vehicle control ECU does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).

·

No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).


·

Incorrect hybrid vehicle control ECU installed

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

The DTC is cleared when the conditions return to normal.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK PART NUMBER (HYBRID VEHICLE CONTROL ECU)
a.

Check that the proper hybrid vehicle control ECU is installed.

OK:

Proper hybrid vehicle control ECU is installed.



Result:
Proceed to
OK
NG



OK

2.CHECK PART NUMBER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

2.CHECK PART NUMBER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Check that the proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.

OK:

Proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.



Result:
Proceed to
OK
NG



OK

3.SYSTEM INFORMATION MEMORIZATION

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
HINT:

After performing "Reset Memory" using the GTS to clear the memorized value of the No. 1 skid control ECU (brake booster with master cylinder assembly), DTC C136F00 will be stored until system information memorization is performed.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
DTC C136F00 is not output. A
DTC C136F00 is output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY