Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C137BA3  Brake System Control Module "A" System Voltage System Voltage High  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 2 skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

This DTC is stored when the +BS terminal voltage deviates due to a malfunction in the power supply or charging circuit such as the auxiliary battery or DC/DC converter circuit, etc.

This DTC is cleared when the voltage at terminal +BS returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C137BA3 Brake System Control Module "A" System Voltage System Voltage High The +BS terminal voltage is higher than 17.4 V for 0.8 seconds or more.
·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C425607C05
1.49,0.479 1.927,0.729 0.438,0.25 2.635,1.656 2.833,1.042 true 0.708,1.646 0.552,1.021 true 1.594,0.521 2.052,0.719 0.458,0.198 10 false A57 0.135,0.135 0.49,0.5 0.354,0.365 10 false *a 2.719,0.823 3.115,1.094 0.396,0.271 10 false +BS 0.313,0.833 0.708,1.104 0.396,0.271 10 false GND1
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-14 (+BS) - Body ground Always 11 to 14 V
A57-14 (+BS) - A57-1 (GND1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CLEAR DTC
a.

Reconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C137BA3 is not output. A
DTC C137BA3 is output. B



A

B