Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C14C616  Electronic Brake Booster Control Module "A" Supply Voltage Circuit Voltage Below Threshold  


DESCRIPTION

Refer to DTC C110E14.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C110E14

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C14C616 Electronic Brake Booster Control Module "A" Supply Voltage Circuit Voltage Below Threshold Either of the following is detected:
·

Any of the following is detected when the ECU internal voltage is 6.92 V or less:

-

When operation of the main relay is requested, the relay output voltage is less than a certain value for 10.05 seconds or more.

-

The stroke sensor value invalid for 10.2 seconds or more.

-

The reaction force pressure sensor value invalid for 10.2 seconds or more.

-

The voltage supplied to the servo pressure sensor is a certain value or less or a certain value or more for 10.06 seconds or more.

-

The servo pressure sensor value invalid for 10.2 seconds or more.

-

The voltage supplied to the reaction force pressure sensor is a certain value or less or a certain value or more for 10.06 seconds or more.


·

When the internal voltage of the ECU is 8.3 V or less, the accumulator pressure sensor value is invalid for 10.8 seconds or more.


·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only DTC C14C616 is output. A
DTCs other than C14C616 are output. B



A

2.CHECK HARNESS AND CONNECTOR (IG1, +BI1 AND BS TERMINAL)

B

2.CHECK HARNESS AND CONNECTOR (IG1, +BI1 AND BS TERMINAL)
a.
C423268C12
0.417,0.75 0.833,1 0.417,0.25 2.865,2.802 2.688,1.844 true 2.458,1.667 2.302,1.073 true 1.229,2.823 1.354,2.156 true 2.156,0.906 2.615,1.104 0.458,0.198 10 false +BI1 0.5,0.781 0.958,0.979 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 2.792,2.844 3.25,3.042 0.458,0.198 10 false BS 1.125,2.844 1.583,3.042 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-31 (IG1) - Body ground Ignition switch ON 11 to 14 V
A44-14 (+BI1) - Body ground Ignition switch ON 11 to 14 V
A44-15 (BS) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
11 to 14 V. A
Below 11 V. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR