The outer mirror switch assembly sends a mirror retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is operated. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the signal.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold SW | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in retract position
ON: Retractable outer mirror switch in retract position |
- |
| Tester Display |
|---|
| Outer Mirror Fold SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the malfunctioning parts.
| Result | Proceed to |
|---|---|
| Both outer rear view mirror assemblies are malfunctioning | A |
| Outer rear view mirror assembly LH is malfunctioning | B |
| Outer rear view mirror assembly RH is malfunctioning | C |
A
B
C
Remove the MIR MTR NO. 1 / MIR MTR NO. 2 relay from No. 2 engine room relay block and No. 2 junction block assembly.
Inspect the MIR MTR NO. 1 / MIR MTR NO. 2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 4 | Auxiliary battery voltage applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 4 | Auxiliary battery voltage not applied between terminals | Below 1 Ω |
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Auxiliary battery voltage not applied between terminals | 10 kΩ or higher |
| 4 - 5 | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (MIR MTR NO. 1 Relay) | B |
| NG (MIR MTR NO. 2 Relay) | C |
A
B
C
| *1 | No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for HV Model *2: for Gasoline Model |
||
| MIR MTR NO. 1 relay terminal 1 - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
| MIR MTR NO. 2 relay terminal 1 - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
| MIR MTR NO. 1 relay terminal 5 - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
| MIR MTR NO. 2 relay terminal 5 - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MIR MTR NO. 1 relay terminal 4 - Body ground | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 4 - Body ground | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 4 - MIR MTR NO. 2 relay terminal 4 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MIR MTR NO. 1 relay terminal 2 - H43-11 (RTRR) | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 2 - H43-10 (RETR) | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 2 or H43-11 (RTRR) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 2 relay terminal 2 or H43-10 (RETR) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J31 outer rear view mirror assembly LH connector.
Disconnect the J15 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MIR MTR NO. 1 relay terminal 3 - J31-12 (MF) | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 3 - J31-5 (MR) | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 3 - J15-12 (MF) | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 3 - J15-5 (MR) | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 3 or J31-12 (MF) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 2 relay terminal 3 or J31-5 (MR) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 1 relay terminal 3 or J15-12 (MF) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 2 relay terminal 3 or J15-5 (MR) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Remove the MIR MTR NO. 1 / MIR MTR NO. 2 relay from No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MIR MTR NO. 2 relay terminal 3 - J31-5 (MR) | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 3 - J31-12 (MF) | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 3 or J31-5 (MR) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 1 relay terminal 3 or J31-12 (MF) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
OK
NG
Remove the MIR MTR NO. 1 / MIR MTR NO. 2 relay from No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MIR MTR NO. 2 relay terminal 3 - J15-5 (MR) | Always | Below 1 Ω |
| MIR MTR NO. 1 relay terminal 3 - J15-12 (MF) | Always | Below 1 Ω |
| MIR MTR NO. 2 relay terminal 3 or J15-5 (MR) - Body Ground | Always | 10 kΩ or higher |
| MIR MTR NO. 1 relay terminal 3 or J15-12 (MF) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J22-10 (MR) - H44-16 (RET) | Always | Below 1 Ω |
| J22-9 (MAT) - H44-6 (AMR) | Always | Below 1 Ω |
| J22-10 (MR) or H44-16 (RET) - Body ground | Always | 10 kΩ or higher |
| J22-9 (MAT) or H44-6 (AMR) - Body ground | Always | 10 kΩ or higher |
| J22-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG