Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL VALVE (for Intake Side of Bank 2) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418433 CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2) A

2GR-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft timing gear bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
Gas leak from exhaust system is repaired Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM
If transaxle compensation code read from ECM:
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UA80F Initialization:(Click here)
for UA80F Registration:(Click here)
If transaxle compensation code not read from ECM:
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Stop and Start System (Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UA80E:(Click here)
for UA80F:(Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 15370C 2.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A368570C01
1.698,1.292 2.188,1.292 true 1.469,1.313 1.198,1.719 1.198,1.719 0.958,1.719 true 2.198,1.198 2.375,1.396 0.177,0.198 10 true *a 0.781,1.646 0.958,1.844 0.177,0.198 10 true *b
*a Timing Mark
*b Timing Mark (Cutout)


Turn the crankshaft pulley clockwise until its timing mark (cutout) is aligned with the timing mark on the timing chain cover assembly as shown in the illustration.


b.

Check that the cutout of the camshaft timing gear assembly is at the top.

A395722C01
2.885,0.781 3.208,0.479 3.208,0.479 3.396,0.479 true 2.219,3.552 2.448,3.552 2.448,3.552 2.719,3.281 true 5.125,3.323 5.125,3.167 5.125,3.167 5.365,3.042 true 5.208,0.896 5.667,0.896 true 0.885,1.104 1.198,1.26 0.313,0.156 10 false *a 0.917,2.906 1.229,3.063 0.313,0.156 10 false *b 5.698,0.792 5.938,1.01 0.24,0.219 10 true *c 1.76,0.823 1.99,1.052 0.229,0.229 10 true *d 5.073,3.323 5.385,3.479 0.313,0.156 10 false *c 1.99,3.479 2.208,3.667 0.219,0.188 10 true *c 3.427,0.375 3.667,0.563 0.24,0.188 10 true *c 1.75,2.656 1.979,2.885 0.229,0.229 10 true *d
*a Correct *b Incorrect
*c Cutout *d Up


HINT:

If the cutout of the camshaft timing gear assembly is not at the top, turn the crankshaft 360° clockwise and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing chain cover assembly again.



Hide 4.REMOVE CAMSHAFT TIMING GEAR BOLT

a.
A454742

While holding the crankshaft pulley, remove the camshaft timing gear bolt.

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

Do not turn the crankshaft pulley after removing the camshaft timing gear bolt.