Home › Engine / Hybrid System › 2GR-FKS (COOLING) › THERMOSTAT › from 2020.11
RM37A0E _51 Engine / Hybrid System _086855 2GR-FKS COOLING _0419160 THERMOSTAT A

2GR-FKS COOLING  THERMOSTAT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during water inlet with thermostat sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

*5: When the starter assembly is replaced, "ST relay" must be also replaced

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UA80F Initialization:(Click here)
for UA80F Registration:(Click here)
Replacement of ECM
If transaxle compensation code read from ECM:
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


If transaxle compensation code not read from ECM:
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of starter assembly*5 Clear the number of starter operations Stop and Start System (Click here)
Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UA80E:(Click here)
for UA80F:(Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 12327 2.REMOVE REAR ENGINE MOUNTING STAY RH

Hide 82121 3.DISCONNECT ENGINE WIRE

a.
A458785

Disconnect the water inlet with thermostat sub-assembly connector.


b.

Remove the bolt.


c.

Disengage the clamp to disconnect the engine wire.


Hide 12315 4.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

Hide 16261 5.DISCONNECT WATER BY-PASS HOSE

a.
A368523

Slide the clip and disconnect the water by-pass hose.


Hide 16031 6.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

a.
A368720

Remove the 2 bolts, 2 nuts and water inlet with thermostat sub-assembly.


b.

Remove the gasket from the water inlet with thermostat sub-assembly.