When the electric parking brake switch is pulled, a lock request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C060962 | Electric Parking Brake Switch Signal Compare Failure | ·
Parking brake switch open or short circuit is detected for 1 second or more ·
Parking brake switch stuck malfunction |
·
Electric parking brake switch (electric parking brake switch assembly) ·
Wire harness or connector ·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | - | - | - |
| Malfunction Status | Parking brake switch open circuit is detected | ○ | - | - |
| Parking brake switch short circuit is detected | - | ○ | - | |
| Parking brake switch stuck malfunction | - | - | ○ | |
| Detection Time | 1 second or more | 1 second or more | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.
Remove the electric parking brake switch (electric parking brake switch assembly).
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL
Inspect the electric parking brake switch (electric parking brake switch assembly).
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P2 electric parking brake switch (electric parking brake switch assembly) connector.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-36 (SWI1) - P2-7 (SWI1) | Always | Below 1 Ω |
| A57-31 (SWO1) - P2-8 (SWO1) | Always | Below 1 Ω |
| A57-41 (SWI2) - P2-1 (SWI2) | Always | Below 1 Ω |
| A57-39 (SWO2) - P2-2 (SWO2) | Always | Below 1 Ω |
| A57-36 (SWI1) or P2-7 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A57-31 (SWO1) or P2-8 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A57-41 (SWI2) or P2-1 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A57-39 (SWO2) or P2-2 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING