Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417507 FUEL INJECTOR(for Port Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17190 4.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 5.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A454387

Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23800 6.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.
A454388C01
0.448,1.656 0.646,1.833 0.198,0.177 10 true *a 2.792,1.521 2.99,1.688 0.198,0.167 10 true *b 1,0.198 1.188,0.385 0.188,0.188 10 true *b
*a Fuel Pressure Sensor Connector
*b No. 5 Engine Wire Connector


Disconnect the fuel pressure sensor connector.


b.

Disconnect the 2 No. 5 engine wire connectors.


c.
A454389

Remove the 4 bolts and fuel delivery pipe with sensor assembly with the 6 port fuel injector assemblies from the intake manifold.

NOTICE:
·

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.

·

When removing the fuel delivery pipe with sensor assembly, hold the pipe by both ends and pull it straight upward.




Hide 23807V 7.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A454390

Remove the 4 No. 1 delivery pipe spacers from the intake manifold.


Hide 23291A 8.REMOVE INJECTOR VIBRATION INSULATOR

a.
A454391

Remove the 6 injector vibration insulators from the intake manifold.


Hide 23250F 9.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.

for Bank 2:

i.
A368855

Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


ii.

Pull the 3 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


iii.
A368856

Disconnect the 3 port fuel injector assembly connectors.



b.

for Bank 1:

i.
A454392

Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


ii.

Pull the 3 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


iii.
A368858

Disconnect the 3 port fuel injector assembly connectors.



c.

Remove the O-ring from each port fuel injector assembly.


d.
A361004N01
2.042,0.365 2.604,0.604 0.563,0.24 10 true No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.