Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420959 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  C123A14  Supply Voltage Circuit IG Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C123A14 Supply Voltage Circuit IG Open
·

Diagnosis Condition:

Ignition switch ON

·

Malfunction Status:

When the ECM is communicating via CAN communication, IG power is not input to the skid control ECU (brake actuator sub-assembly).

·

Detection Time:

Approximately 15 seconds


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C453606E01
0.615,1.406 2.844,1.76 2.229,0.354 10 false from Stop and Start Syatem*1 2.177,2.365 3.427,2.844 1.25,0.479 10 false ECU-IG1 NO. 2*2 3.885,1.24 4.177,1.646 0.292,0.406 10 false 45 4.188,1.417 4.906,1.823 0.719,0.406 10 false IG1 4.198,2.135 4.917,2.542 0.719,0.406 10 false A39 4.188,2.323 5.729,2.885 1.542,0.563 10 false Skid Control ECU (Brake Actuator Assembly) 3.813,3.052 6.781,3.385 2.969,0.333 10 false *1: w/ Stop and Start System 3.813,3.375 6.781,3.708 2.969,0.333 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
C342413C26
1.458,0.125 1.875,0.375 0.417,0.25 2.5,1.823 2.365,1.354 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A39 2.438,1.844 2.896,2.042 0.458,0.198 10 false IG1 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Result Proceed to
OK A
NG (w/ Stop and Start System) B
NG (w/o Stop and Start System) C



A

B

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR