Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420959 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C453607E02
0.458,0.969 1.688,1.167 1.229,0.198 10 false ABS NO. 2 0.365,2.292 1.594,2.49 1.229,0.198 10 false ECU-IG1 NO. 2*2 2.833,1.823 3.177,2.042 0.344,0.219 10 false A39 5.135,1.552 7.01,2.031 1.875,0.479 10 false Combination Meter Assembly 2.833,1.969 4.385,2.677 1.552,0.708 10 false Skid Control ECU (Brake Actuator Assembly) 2.802,0.781 4.031,0.979 1.229,0.198 10 false +BS 2.813,1.385 4.042,1.583 1.229,0.198 10 false IG1 2.552,0.677 2.927,0.896 0.375,0.219 10 false 14 2.552,1.271 2.927,1.49 0.375,0.219 10 false 45 0.917,3.219 3.344,3.719 2.427,0.5 10 false : CAN Communication Line 0.146,1.396 1.104,2.021 0.958,0.625 10 false from Stop and Start Syatem*1 4.583,3 6.677,3.5 2.094,0.5 10 false *1: w/ Stop and Start System 4.583,3.333 6.75,3.792 2.167,0.458 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.INSPECT COMBINATION METER ASSEMBLY

B

INSPECT REAR BRAKE

C

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Park
50004 122 69

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.
C342413C25
1.458,0.125 1.875,0.375 0.417,0.25 2.969,1.813 2.698,0.99 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A39 2.896,1.854 3.354,2.052 0.458,0.198 10 false +BS 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-14 (+BS) - Body ground Always 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Result Proceed to
OK A
NG (w/ Stop and Start System) B
NG (w/o Stop and Start System) C



A

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)

B

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.
C342413C26
1.458,0.125 1.875,0.375 0.417,0.25 2.5,1.823 2.365,1.354 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A39 2.438,1.844 2.896,2.042 0.458,0.198 10 false IG1 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR