Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch is ON.

Conditions required for operation standby:

(a)

The driver door is closed.

(b)

The driver seat belt is fastened.

(c)

The system is normal.



HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system



WIRING DIAGRAM

C427349E02
0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.896,1.74 1.51,1.938 0.615,0.198 10 false CANH 0.104,3.917 0.719,4.115 0.615,0.198 10 false H21 0.104,4.094 2.031,4.375 1.927,0.281 10 false Combination Meter Assembly 1.396,0.75 1.708,0.948 0.313,0.198 10 false 31 1.385,1.552 1.698,1.75 0.313,0.198 10 false 32 5.083,0.75 5.396,0.948 0.313,0.198 10 false 43 5.094,1.552 5.406,1.75 0.313,0.198 10 false 27 4.51,2.76 4.865,2.979 0.354,0.219 10 false 10 4.115,2.969 4.531,3.219 0.417,0.25 10 false SLT1 3.646,2.969 4.094,3.229 0.448,0.26 10 false E 3.396,2.76 3.74,3 0.344,0.24 10 false 12 5.083,2.76 5.396,2.958 0.313,0.198 10 false 35 5.375,0.927 5.99,1.125 0.615,0.198 10 false CANL 5.375,1.74 5.99,1.938 0.615,0.198 10 false CANH 5.344,3.042 5.906,3.292 0.563,0.25 10 false PKB 3.01,3.229 3.625,3.427 0.615,0.198 10 false P2 3.01,3.375 5.219,3.99 2.208,0.615 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 2.927,4.344 5.021,4.604 2.094,0.26 10 false : CAN Communication Line 5.302,3.948 5.917,4.146 0.615,0.198 10 false A39 5.302,4.104 6.854,4.49 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver door is closed.

2.

The driver seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (BRAKE HOLD READY)
2.READ VALUE USING GTS (BRAKE HOLD READY)
a.

Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Hold Ready
50003 435 164
Standard:
Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation Mode Condition Display Brake Hold Standby Indicator Light
Not pressed Not in stand-by mode Does not come on
Pressing the brake hold switch (electric parking brake switch assembly) Stand-by mode Come on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

B

C

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the brake hold switch (electric parking brake switch assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>INSPECTION

OK:

The brake hold switch (electric parking brake switch assembly) operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P2-10 (SLT1) - A39-35 (PKB) Always Below 1 Ω
P2-10 (SLT1) or A39-35 (PKB) - Body ground Always 10 kΩ or higher
P2-12 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR