Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY › from 2020.11
RM37A0E _59 Vehicle Exterior _086888 LIGHTING (EXT) _0416588 REAR COMBINATION LIGHT ASSEMBLY A

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear combination light assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Rear bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Rear bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81498 1.REMOVE REAR COMBINATION LIGHT COVER

a.
E430171C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction


Using a moulding remover, disengage the 2 claws and guide as shown in the illustration.


b.
E430173C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides to remove the rear combination light cover as shown in the illustration.


Hide 2.REMOVE REAR COMBINATION LIGHT SUB-ASSEMBLY

a.
E430175C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear combination light sub-assembly as shown in the illustration.


b.
E430176

Remove the 2 screws.


c.
E430177C01
1.417,1.104 1.01,1.438 true 0.99,0.625 0.698,0.927 true 1.823,1.708 1,2.083 1,2.083 1.521,1.76 true 0.802,1.469 1.115,1.625 0.313,0.156 10 true *a 0.552,0.969 0.865,1.125 0.313,0.156 10 true *b 0.667,2 0.979,2.156 0.313,0.156 10 true *b
*a Pin
*b Guide
V113147

Remove in this Direction


Pull the rear combination light sub-assembly toward the rear of the vehicle as shown in the illustration to disengage the pin and 3 guides and separate the rear combination light sub-assembly.

NOTICE:

To prevent the rear combination light sub-assembly from falling when disengaging the pin and 3 guides, make sure to hold the rear combination light sub-assembly.



d.
E430179

Disengage the 2 guides.


e.

Disconnect 3 connectors to remove the rear combination light sub-assembly.


Hide 3.REMOVE REAR BUMPER ASSEMBLY

Hide 52563D 4.REMOVE REAR BUMPER UPPER RETAINER

Hide 81565D 5.REMOVE REAR COMBINATION LIGHT CORD

a.
E430180

Disconnect the connector to remove the rear combination light cord.