Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

Signals are input into the position control ECU assembly (driver seat). The built-in ECU manages the signals received from the power seat switch and operates each motor. If the position control ECU assembly (driver seat) receives more than 2 motor operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly (driver seat) receives only 1 signal.

WIRING DIAGRAM

B567711E15
1,0.271 2.885,0.563 1.885,0.292 10 false from Auxiliary Battery 0.99,0.833 2.875,1.125 1.885,0.292 10 false from Auxiliary Battery 1,1.406 2.885,1.698 1.885,0.292 10 false from IG1-NO. 1 Relay 3.229,0.469 5.115,0.76 1.885,0.292 10 false ECU-DCC NO. 2 3.375,1.208 5.26,1.5 1.885,0.292 10 false P/SEAT F/R*2 3.271,1.583 5.156,1.875 1.885,0.292 10 false ECU-IG1 NO. 4 4.802,0.313 5.292,0.542 0.49,0.229 10 false e25 4.813,1.417 5.302,1.646 0.49,0.229 10 false e25 6.427,0.792 6.917,1.021 0.49,0.229 10 false e23 4.813,2.25 5.302,2.479 0.49,0.229 10 false e25 4.844,0.083 5.333,0.313 0.49,0.229 10 false 15 4.885,0.635 5.375,0.865 0.49,0.229 10 false 3 4.885,1.177 5.375,1.406 0.49,0.229 10 false 1 4.854,2.01 5.344,2.24 0.49,0.229 10 false 12 5.24,0.292 5.885,0.573 0.646,0.281 10 false SYSB 5.24,0.854 5.885,1.135 0.646,0.281 10 false +B 5.24,1.417 5.885,1.698 0.646,0.281 10 false IG 5.229,2.25 5.875,2.531 0.646,0.281 10 false SGND 4.781,2.917 6.74,3.458 1.958,0.542 10 false Position Control ECU Assembly (Driver Seat) 0.875,2.635 1.833,2.917 0.958,0.281 10 false e17*1, e33*2 0.885,2.792 3.25,3.458 2.365,0.667 10 false Front Power Seat Switch (Driver Seat) 2.74,2.135 3.625,2.375 0.885,0.24 10 false 20*1, 11*2 4.823,0.865 5.313,1.094 0.49,0.229 10 false e23 6.5,0.563 6.99,0.792 0.49,0.229 10 false 2 5.969,0.792 6.615,1.073 0.646,0.281 10 false GND 2.521,2.26 3.01,2.49 0.49,0.229 10 false E 3.375,1.031 5.26,1.323 1.885,0.292 10 false P/SEAT F/L*1 0.906,3.396 1.865,3.677 0.958,0.281 10 false *1: for LHD 1.813,3.385 2.771,3.667 0.958,0.281 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
All power seat functions do not operate A
One or more power seat functions do not operate B



A

2.INSPECT FRONT POWER SEAT SWITCH (DRIVER SEAT)

B

GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate)

2.INSPECT FRONT POWER SEAT SWITCH (DRIVER SEAT)

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SUPPLY)

NG

REPLACE FRONT POWER SEAT SWITCH (DRIVER SEAT)

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SUPPLY)
a.

Disconnect the e23 and e25 position control ECU assembly (driver seat) connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e23-3 (+B) - Body ground Ignition switch off*1
Always*2
11 to 14 V
e25-15 (SYSB) - Body ground Ignition switch off*1
Always*2
11 to 14 V
e25-1 (IG) - Body ground Ignition switch ON 11 to 14 V
e25-1 (IG) - Body ground Ignition switch off Below 1 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e23-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (DRIVER SEAT) - POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (DRIVER SEAT) - POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-12 (SGND) - e17-20 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR