Signals are input into the position control ECU assembly (driver seat). The built-in ECU manages the signals received from the position control ECU assembly (driver seat) and operates each motor. If the position control ECU assembly (driver seat) receives 2 or more operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly (driver seat) receives only 1 signal.
Check that each function of the power seat operates normally by using the front power seat switch (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| One or more power seat functions do not operate | A |
| All power seat functions do not operate | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off |
- |
| Lumbar Switch Front | Lumbar support adjuster switch signal (Forward) | ON or OFF | ON: Lumbar support adjuster switch (Forward) on
OFF: Lumbar support adjuster switch (Forward) off |
- |
| Lumbar Switch Rear | Lumbar support adjuster switch signal (Rearward) | ON or OFF | ON: Lumbar support adjuster switch (Rearward) on
OFF: Lumbar support adjuster switch (Rearward) off |
- |
| Tester Display |
|---|
| Reclining Rear |
| Reclining Front |
| Front Vertical Down |
| Front Vertical Up |
| Lifter Switch Down |
| Lifter Switch Up |
| Slide Rear |
| Slide Front |
| Lumbar Switch Front |
| Lumbar Switch Rear |
On the GTS screen, ON or OFF is displayed accordingly
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Lumbar Slide | Lumbar support operation (Forward - Rearward) | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
| Tester Display |
|---|
| Front Vertical Operation |
| Tester Display |
|---|
| Lifter Operation |
| Tester Display |
|---|
| Seat Slide Operation |
| Tester Display |
|---|
| Lumbar Slide |
| Result | Proceed to |
|---|---|
| All power seat functions operate normally | A |
| Slide function does not operate normally | B |
| Front vertical function does not operate normally | C |
| Lifter function does not operate normally | D |
| Reclining function does not operate normally | E |
| Lumbar support adjustment function does not operate normally | F |
A
B
C
D
E
F
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e23 and e24 position control ECU assembly (driver seat) connectors.
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.
for LHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-1 (SLD+) - e11-4 | Always | Below 1 Ω |
| e23-1 (SLD+) or e11-4 - Body ground | Always | 10 kΩ or higher |
| e23-5 (SLD-) - e11-1 | Always | Below 1 Ω |
| e23-5 (SLD-) or e11-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-7 (FRV+) - e12-1 | Always | Below 1 Ω |
| e23-7 (FRV+) or e12-1 - Body ground | Always | 10 kΩ or higher |
| e24-4 (FRV-) - e12-4 | Always | Below 1 Ω |
| e24-4 (FRV-) or e12-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-6 (LFT+) - e13-1 | Always | Below 1 Ω |
| e23-6 (LFT+) or e13-1 - Body ground | Always | 10 kΩ or higher |
| e24-5 (LFT-) - e13-4 | Always | Below 1 Ω |
| e24-5 (LFT-) or e13-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-10 (RCL+) - g5-4 | Always | Below 1 Ω |
| e23-10 (RCL+) or g5-4 - Body ground | Always | 10 kΩ or higher |
| e24-6 (RCL-) - g5-1 | Always | Below 1 Ω |
| e24-6 (RCL-) or g5-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-9 (L+) - g6-1 | Always | Below 1 Ω |
| e23-9 (L+) or g6-1- Body ground | Always | 10 kΩ or higher |
| e24-3 (L-) - g6-2 | Always | Below 1 Ω |
| e24-3 (L-) or g6-2 - Body ground | Always | 10 kΩ or higher |
for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-1 (SLD+) - e28-4 | Always | Below 1 Ω |
| e23-1 (SLD+) or e28-4 - Body ground | Always | 10 kΩ or higher |
| e23-5 (SLD-) - e28-1 | Always | Below 1 Ω |
| e23-5 (SLD-) or e28-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-7 (FRV+) - e29-1 | Always | Below 1 Ω |
| e23-7 (FRV+) or e29-1 - Body ground | Always | 10 kΩ or higher |
| e24-4 (FRV-) - e29-4 | Always | Below 1 Ω |
| e24-4 (FRV-) or e29-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-6 (LFT+) - e30-1 | Always | Below 1 Ω |
| e23-6 (LFT+) or e30-1 - Body ground | Always | 10 kΩ or higher |
| e24-5 (LFT-) - e30-4 | Always | Below 1 Ω |
| e24-5 (LFT-) or e30-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-10 (RCL+) - g7-4 | Always | Below 1 Ω |
| e23-10 (RCL+) or g7-4 - Body ground | Always | 10 kΩ or higher |
| e24-6 (RCL-) - g7-1 | Always | Below 1 Ω |
| e24-6 (RCL-) or g7-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-9 (L+) - g8-1 | Always | Below 1 Ω |
| e23-9 (L+) or g8-1- Body ground | Always | 10 kΩ or higher |
| e24-3 (L-) - g8-2 | Always | Below 1 Ω |
| e24-3 (L-) or g8-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
for LHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-20 (E) - e25-12 (SGND) | Always | Below 1 Ω |
| e17-20 (E) or e25-12 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-6 (SLDR) - e25-23 (SLDR) | Always | Below 1 Ω |
| e17-6 (SLDR) or e25-23 (SLDR) - Body ground | Always | 10 kΩ or higher |
| e17-7 (SLDF) - e25-9 (SLDF) | Always | Below 1 Ω |
| e17-7 (SLDF) or e25-9 (SLDF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-1 (RCLR) - e25-22 (RCLR) | Always | Below 1 Ω |
| e17-1 (RCLR) or e25-22 (RCLR) - Body ground | Always | 10 kΩ or higher |
| e17-2 (RCLF) - e25-8 (RCLF) | Always | Below 1 Ω |
| e17-2 (RCLF) or e25-8 (RCLF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-4 (FUP) - e25-6 (FRVU) | Always | Below 1 Ω |
| e17-4 (FUP) or e25-6 (FRVU) - Body ground | Always | 10 kΩ or higher |
| e17-5 (FDWN) - e25-20 (FRVD) | Always | Below 1 Ω |
| e17-5 (FDWN) or e25-20 (FRVD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-3 (LUP) - e25-7 (LFTU) | Always | Below 1 Ω |
| e17-3 (LUP) or e25-7 (LFTU) - Body ground | Always | 10 kΩ or higher |
| e17-8 (LDWN) - e25-21 (LFTD) | Always | Below 1 Ω |
| e17-8 (LDWN) or e25-21 (LFTD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e17-17 (R) - e25-18 (LFLR) | Always | Below 1 Ω |
| e17-17 (R) or e25-18 (LFLR) - Body ground | Always | 10 kΩ or higher |
| e17-14 (H) - e25-4 (LFLF) | Always | Below 1 Ω |
| e17-14 (H) or e25-4 (LFLF) - Body ground | Always | 10 kΩ or higher |
for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-11 (E) - e25-12 (SGND) | Always | Below 1 Ω |
| e33-11 (E) or e25-12 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-5 (SLDR) - e25-23 (SLDR) | Always | Below 1 Ω |
| e33-5 (SLDR) or e25-23 (SLDR) - Body ground | Always | 10 kΩ or higher |
| e33-4 (SLDF) - e25-9 (SLDF) | Always | Below 1 Ω |
| e33-4 (SLDF) or e25-9 (SLDF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-10 (RCLR) - e25-22 (RCLR) | Always | Below 1 Ω |
| e33-10 (RCLR) or e25-22 (RCLR) - Body ground | Always | 10 kΩ or higher |
| e33-9 (RCLF) - e25-8 (RCLF) | Always | Below 1 Ω |
| e33-9 (RCLF) or e25-8 (RCLF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-7 (FUP) - e25-6 (FRVU) | Always | Below 1 Ω |
| e33-7 (FUP) or e25-6 (FRVU) - Body ground | Always | 10 kΩ or higher |
| e33-6 (FDWN) - e25-20 (FRVD) | Always | Below 1 Ω |
| e33-6 (FDWN) or e25-20 (FRVD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-8 (LUP) - e25-7 (LFTU) | Always | Below 1 Ω |
| e33-8 (LUP) or e25-7 (LFTU) - Body ground | Always | 10 kΩ or higher |
| e33-3 (LDWN) - e25-21 (LFTD) | Always | Below 1 Ω |
| e33-3 (LDWN) or e25-21 (LFTD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e33-14 (R) - e25-18 (LFLR) | Always | Below 1 Ω |
| e33-14 (R) or e25-18 (LFLR) - Body ground | Always | 10 kΩ or higher |
| e33-17 (H) - e25-4 (LFLF) | Always | Below 1 Ω |
| e33-17 (H) or e25-4 (LFLF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG