When the front wiper deicer switch is operated, the operation signal is transmitted to the air conditioning amplifier assembly directly. When the air conditioning amplifier assembly receives the signal, it turns on the DEICER relay to operate the windshield deicer system.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the windshield deicer system may not operate.
The windshield deicer system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the air conditioning system can be operated using the remote touch.
Both the windshield deicer system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for HV Model: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model with Automatic Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model with Manual Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Deicer Relay (Front) | Windshield deicer wire (windshield glass) | OFF or ON | - |
| Tester Display |
|---|
| Deicer Relay (Front) |
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning amplifier assembly with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Check that the windshield deicer system operates normally.
The windshield deicer system operates normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 8 Inch Display) | B |
| NG (for 12.3 Inch Display) | C |
A
B
C
Replace the integration control sub-assembly with a new or known good one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL
Check that the windshield deicer system operates normally.
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Auxiliary battery voltage not applied between terminals | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | DEICER Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay holder terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| DEICER relay holder terminal 3 - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | DEICER Relay Holder |
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay holder terminal 1 - H62-22 (FDEF) | Always | Below 1 Ω |
| DEICER relay holder terminal 1 or H62-22 (FDEF) - Body ground | Always | 10 kΩ higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H62 air conditioning amplifier assembly connector.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H62-22 (FDEF) - H62-17 (GND) | Ignition switch ON, Front wiper deicer switch on | Below 1 V |
| H62-22 (FDEF) - H62-17 (GND) | Ignition switch ON, Front wiper deicer switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | DEICER Relay Holder |
Disconnect the A60 windshield deicer wire (windshield glass) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay holder terminal 5 - A60-1 (B) | Always | Below 1 Ω |
| DEICER relay holder terminal 5 - A60-3 (B2) | Always | Below 1 Ω |
| A60-1 (B) - Body ground | Always | 10 kΩ higher |
| A60-3 (B2) - Body ground | Always | 10 kΩ higher |
| DEICER relay holder terminal 5 - Body ground | Always | 10 kΩ higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A60-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG