Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2020.11
RM37A0E _55 Steering _086875 STEERING COLUMN _0418168 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.
C425034C01
0.917,3.385 1.094,3.573 0.177,0.188 10 true *a 2.354,3.375 2.531,3.563 0.177,0.188 10 true *a 2.188,4.063 2.365,4.25 0.177,0.188 10 true *b
*a Nut
*b Bolt


Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After temporarily tightening the bolt, fully tighten the 2 nuts then fully tighten the bolt.

·

After the column is installed, check the tilt and telescopic operation.

·

If a large amount of force is required to operate the tilt and telescopic mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt and telescopic operation works smoothly.

Tighten the nuts and check the tilt and telescopic operation again.




b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C425032C01
1.51,0.458 0.656,0.479 0.656,0.479 1.542,0.5 true 0.469,0.385 0.646,0.573 0.177,0.188 10 true *a
*a Matchmark
V113147

Install in this direction


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Install the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C425033

Tighten the clamp.


Hide 45253 4.INSTALL STEERING COLUMN HOLE COVER

a.
C425029

Install the steering column hole cover with the 2 clips.


b.

Install the clip.


c.

Return the floor carpet.


Hide 45220 5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.INSTALL FRONT WHEEL LH (for LHD)

Hide 7.INSTALL FRONT WHEEL RH (for RHD)

Hide 73900 8.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C425028C01
1.927,0.594 2.323,0.594 false 2.354,0.51 2.667,0.667 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 10.INSTALL UPPER STEERING COLUMN COVER

a.
C425025

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C425026C01
0,0 0,0 false
V113147

Install in this direction


Engage the claw to install the upper steering column cover.


Hide 45287 11.INSTALL LOWER STEERING COLUMN COVER

a.
C431432

Engage the 2 claws to install the lower steering column cover.


b.
C431430

Install the 3 screws.


Hide 12.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 13.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 14.INSTALL STEERING WHEEL ASSEMBLY

Hide 15.CHECK STEERING WHEEL CENTER POINT

Hide 45130 16.INSTALL HORN BUTTON ASSEMBLY

Hide 17.PERFORM INITIALIZATION AND CALIBRATION (for Gasoline Model)

Hide 18.PERFORM INITIALIZATION AND CALIBRATION (for HV Model)