Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › from 2020.11
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0421227 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

for A25A-FXS, A25B-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 81150 4.REMOVE HEADLIGHT ASSEMBLY LH (for LH Side)

Hide 85330 5.REMOVE WINDSHIELD WASHER JAR ASSEMBLY (for LH Side)

a.
B566210

Remove the bolt.


b.
B566211

Remove the 2 bolts, nut and separate the windshield washer jar assembly.


Hide 89173 6.REMOVE FRONT AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the front airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



d.
B566196

Remove the bolt and disengage the claw to remove the front airbag sensor.