Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417921 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B2357  Lost Communication with Wiper Module  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B2357 Lost Communication with Wiper Module
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly


Malfunction Time:

10 seconds or more


·

Windshield wiper relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

WIPER relay


○ Main Body

WIRING DIAGRAM

E435525E01
0.208,3.583 1.698,4.323 1.49,0.74 10 false Windshield Wiper Relay Assembly 5.271,3.271 6.896,3.76 1.625,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.958,4.365 4.323,4.563 3.365,0.198 10 false : CXPI Communication Line 5.375,2.188 5.99,2.385 0.615,0.198 10 false CXP1 5.385,1.031 6,1.229 0.615,0.198 10 false WPS 2.854,0.417 4.5,0.698 1.646,0.281 10 false from Auxiliary Battery 3.948,1.031 7.156,1.24 3.208,0.208 10 false WIPER 5.99,0.552 6.604,0.75 0.615,0.198 10 false IG 6.354,0.552 6.969,0.75 0.615,0.198 10 false B 3.365,1.021 6.688,1.229 3.323,0.208 10 false 2 2.635,1.021 5.958,1.229 3.323,0.208 10 false 1 2.656,0.771 5.979,0.979 3.323,0.208 10 false 3 3.375,0.771 6.698,0.979 3.323,0.208 10 false 5 1.281,0.906 4.646,1.104 3.365,0.198 10 false +B 1.104,2.198 4.469,2.396 3.365,0.198 10 false MPX1 1.354,2.729 4.719,2.927 3.365,0.198 10 false E 1.26,3.26 4.625,3.458 3.365,0.198 10 false ES 5.021,1.156 5.635,1.354 0.615,0.198 10 false H43 5.021,2.188 5.635,2.385 0.615,0.198 10 false H44 5.094,1.969 5.708,2.167 0.615,0.198 10 false 5 5.052,0.927 5.667,1.125 0.615,0.198 10 false 21 1.615,0.885 2.229,1.083 0.615,0.198 10 false A6 1.615,3.271 2.229,3.469 0.615,0.198 10 false A7 1.656,3.031 2.271,3.229 0.615,0.198 10 false 5 1.656,0.667 2.271,0.865 0.615,0.198 10 false 8 1.625,2.74 2.24,2.938 0.615,0.198 10 false A6 1.656,2.51 2.271,2.708 0.615,0.198 10 false 3 1.615,2.208 2.229,2.406 0.615,0.198 10 false A7 1.667,1.979 2.281,2.177 0.615,0.198 10 false 4 2.823,1.448 6.031,1.656 3.208,0.208 10 false WIPER

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the A7 windshield wiper relay assembly connector.


b.

Disconnect the H44 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-4 (MPX1) - H44-5 (CXP1) Always Below 1 Ω
A7-4 (MPX1) or H44-5 (CXP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E395641C02
1.521,0.25 1.938,0.5 0.417,0.25 1.802,1.583 2.052,1.073 true 0.104,0.167 0.417,0.365 0.313,0.198 10 false *a 1.594,0.292 1.906,0.49 0.313,0.198 10 false H44 1.615,1.615 2.01,1.813 0.396,0.198 10 false CXP1
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)


a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H44-5 (CXP1) - Body ground Ignition switch ON Pulse generation
Less than approximately 100 seconds after ignition switch turned off
Approximately 100 seconds or more after ignition switch turned off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wiper Power Relay Function to operate the IG1 WIP relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Wiper Power Relay
50004 123 76
OK:

IG1 WIP relay operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

NG

9.INSPECT WIPER RELAY
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)
a.

Disconnect the A6 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-3 (E) - Body ground Always Below 1 Ω
A7-5 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-8 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds or more after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

6.INSPECT WIPER RELAY
6.INSPECT WIPER RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)

NG

REPLACE WIPER RELAY

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (WIPER relay) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WIPER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WIPER RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-8 (+B) - 3 (WIPER relay) Always Below 1 Ω
A6-8 (+B) or 3 (WIPER relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WIPER RELAY
a.

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE WIPER RELAY

10.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (WIPER relay) - H43-21 (WPS) Always Below 1 Ω
2 (WIPER relay) or H43-21 (WPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (WIPER RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (WIPER RELAY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (WIPER relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR