Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › from 2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0420822 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
for HV Model
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

Hide 2.REMOVE FRONT WHEEL

Hide 47313J 3.SEPARATE FRONT FLEXIBLE HOSE

a.
C423885

Remove the bolt and separate the front flexible hose from the front shock absorber assembly.


Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.



Hide 43512 5.REMOVE FRONT DISC

Hide 43502D 6.REMOVE FRONT AXLE HUB BOLT

a.
C423928C01
1.75,0.917 1.76,0.177 1.76,0.177 1.917,0.177 true 2.167,0.771 2.948,0.771 2.948,0.771 2.948,1.083 true 2.375,0.917 2.938,0.917 true 1.948,0.094 2.26,0.271 0.313,0.177 10 true SST 2.865,1.094 3.177,1.292 0.313,0.198 10 false *a
*a Service Nut


Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the front axle hub bolts.



Hide 43502D 7.INSTALL FRONT AXLE HUB BOLT

a.

Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.


b.
C369719C03
0.635,1.552 0.635,0.844 true 0.885,0.49 1.302,0.49 true 1.333,0.427 1.49,0.594 0.156,0.167 10 true *a 0.583,1.583 0.76,1.74 0.177,0.156 10 false *b
*a Service Nut
*b Washer


Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 front axle hub bolts.


Hide 43512 8.INSTALL FRONT DISC

Hide 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
192 N*m (1958 kgf*cm, 142 ft.*lbf)

NOTICE:
·

Do not twist the front flexible hose when installing the front disc brake caliper assembly.

·

Make sure that there is no foreign matter on the threads of the bolt.




Hide 47313J 10.INSTALL FRONT FLEXIBLE HOSE

a.
C423930C01
0,0 0,0 false
V100135

Hook


Engage the 2 hooks to install the front speed sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C423885

Install the front flexible hose and front speed sensor to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



Hide 11.INSTALL FRONT WHEEL

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

for LHD:

i.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


d.

Turn the ignition switch to ON (READY).


e.

Depress the brake pedal and release it.