Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › from 2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417446 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
for HV Model
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

Hide 2.REMOVE REAR WHEEL

Hide 890C0A 3.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 47850 4.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake cylinder assembly from hanging by the rear flexible hose.



Hide 5.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

a.

Remove the 2 bolts and rear disc brake cylinder mounting with the 2 rear disc brake pads from the rear axle carrier sub-assembly.


Hide 42431 6.REMOVE REAR DISC

Hide 42312E 7.REMOVE REAR AXLE HUB BOLT

a.
C424668C01
0.677,1.292 0.677,1.073 0.677,1.073 1.094,1.073 true 1.396,1.656 1.24,1.656 1.24,1.656 1.24,1.406 true 1.656,0.802 1.656,0.583 1.656,0.583 1.938,0.583 true 0.604,1.333 0.813,1.531 0.208,0.198 10 true *a 1.969,0.521 2.281,0.698 0.313,0.177 10 true SST 1.417,1.563 1.625,1.76 0.208,0.198 10 true *a
*a Service Nut


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09628-10011  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 8.INSTALL REAR AXLE HUB BOLT

a.
C424669C01
2.833,1.469 2.833,0.865 true 2.104,0.448 2.49,0.448 true 1.938,0.365 2.188,0.573 0.25,0.208 10 true *a 2.76,1.51 3,1.677 0.24,0.167 10 true *b
*a Service Nut
*b Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 9.INSTALL REAR DISC

Hide 10.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

a.

Install the rear disc brake cylinder mounting with the 2 rear disc brake pads to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.



Hide 47850 11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 890C0A 12.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 13.INSTALL REAR WHEEL

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

for LHD:

i.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


d.

Turn the ignition switch to ON (READY).


e.

Depress the brake pedal and release it.