Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
89710
1.REMOVE POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
87501B
2.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
73240
3.REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
4.REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
71074S
5.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER
Disconnect the rubber band of the separate type front seatback cover.
71868N
6.REMOVE FRONT SEAT FRONT CUSHION SHIELD
Remove the clip.
|
Remove in this Direction |
Disengage the guide as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws as shown in the illustration.
Disengage the 3 guides to remove the front seat front cushion shield.
71812D
7.REMOVE FRONT SEAT CUSHION SHIELD
Disengage the 2 claws and 2 guides.
Disengage the 2 claws.
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and slightly pull the front seat cushion shield as shown in the illustration.
|
Remove in this Direction |
Disengage the guide as shown in the illustration.
Disconnect the front power seat switch connector to remove the front seat cushion shield.
71862
8.REMOVE FRONT SEAT INNER CUSHION SHIELD
|
Remove in this Direction |
Disengage the 2 claws and 2 guides as shown in the illustration.
Disengage the 2 claws to remove the front seat inner cushion shield.
84921B
9.REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Using a moulding remover, disengage the 4 claws to remove the slide and vertical power seat switch knob.
84921A
10.REMOVE RECLINING POWER SEAT SWITCH KNOB
Using a moulding remover, disengage the 4 claws to remove the reclining power seat switch knob.
72714
11.REMOVE SEAT ADJUSTER SHIELD CLAMP BRACKET
Remove the 2 screws and seat adjuster shield clamp bracket from the front seat cushion shield.
84922C
12.REMOVE FRONT POWER SEAT SWITCH
13.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Disengage the 2 hooks.
Disengage the claw and 4 clamps to separate the front seat airbag assembly wire harness.
Disengage the 4 clamps first.
Disconnect the connector.
Disengage the clamp.
w/ Seat Heater System:
Disengage the clamp.
Disconnect the connector.
Remove the 4 bolts.
Disengage the 4 guides to remove the separate type front seatback assembly from the separate type front seat cushion assembly.
71930A
14.REMOVE FRONT SEAT HEADREST SUPPORT ASSEMBLY
Disengage the 3 hooks.
w/ Seat Heater System:
Disengage the clamp.
Open the 2 fasteners.
Disengage the 4 claws and remove the 2 front seat headrest support assemblies.
15.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Remove the separate type front seatback cover with pad.
71074S
16.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Using a screwdriver, disengage the 9 claws and remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
| *a | Screwdriver | - | - |
87510N
17.REMOVE FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
73920A
18.REMOVE FRONT SEAT AIRBAG ASSEMBLY
85867A
19.REMOVE SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System (w/ Lumbar Support))
| *a | Wire Harness Clamp |
| *b | Hook |
Disengage the wire harness clamp and disconnect the connector.
Disengage the 2 claws and 2 hooks and remove the seatback climate control blower.
72760D
20.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)
8219B
21.REMOVE FRONT SEAT NO. 2 WIRE (for Driver Side)
Disengage the 2 clamps to remove the front seat No. 2 wire.
8219A
22.REMOVE FRONT SEAT NO. 2 WIRE (for Front Passenger Side)
w/ Climate Control Seat System:
Disengage the clamp (A) and disconnect the connector (B).
| *A | for RHD | *B | for LHD |
Disengage the 2 clamps (C) and disconnect the connector (D) to remove the front seat No. 2 wire.
71054S
23.REMOVE FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)
Disengage the 2 claws to separate the 2 front No. 2 seatback edge protectors from the front seatback frame sub-assembly.
|
Remove in this Direction |
Remove the front seatback spring sub-assembly from the front seatback frame sub-assembly as shown in the illustration.
w/ Seatback Felt:
Remove the seatback felt from the front seatback spring sub-assembly.
71588
24.REMOVE FRONT NO. 2 SEATBACK EDGE PROTECTOR
w/o Lumbar Support:
Remove the 2 front No. 2 seatback edge protectors from the front seatback spring sub-assembly.
w/ Lumbar Support:
Remove the 2 front No. 2 seatback edge protectors from the lumbar support adjuster assembly.
71759D
25.REMOVE FRONT NO. 2 SEATBACK HOOK
Remove the 2 front No. 2 seatback hooks from the front seatback frame sub-assembly.
26.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
for Front Passenger Side:
|
Remove in this Direction |
Disengage the claw to separate the connector holder as shown in the illustration.
w/ Seat Heater System:
Disconnect the connector.
Disengage the clamp.
Disengage the 10 hooks and remove the separate type front seat cushion cover with pad from the separate type front seat cushion spring assembly.
71072S
27.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Using a screwdriver, disengage the 14 claws and remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
| *a | Screwdriver | - | - |
87510L
28.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
85860A
29.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)
Disengage the wire harness clamp and disconnect the connector.
Remove the 2 bolts.
Disengage the hook and remove the seat cushion climate control blower assembly.
71876
30.REMOVE RECLINING ADJUSTER INSIDE COVER LH
for LH Side:
Disengage the 4 claws to remove the reclining adjuster inside cover LH.
for RH Side:
Disengage the 4 claws to remove the reclining adjuster inside cover LH.
71874
31.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH
for LH Side:
| *a | Hook |
| *b | Guide |
Disengage the hook.
Disengage the 2 claws and 2 guides to remove the front seat lower cushion shield LH.
for RH Side:
| *a | Hook |
| *b | Guide |
Disengage the hook.
Disengage the claw and guide to remove the front seat lower cushion shield LH.
82192
32.REMOVE FRONT SEAT WIRE
Disconnect each connector and disengage each clamp to remove the front seat wire.
71052A
33.REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Disengage the 6 hooks to remove the front seat cushion spring sub-assembly from the front seat adjuster assembly.
7181B
34.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER
Remove the 2 screws.
|
Remove in this Direction |
Disengage the 2 claws.
Disengage the guide to remove the front seat cushion wire harness holder as shown in the illustration.
71874U
35.REMOVE FRONT LH SEAT LOWER CUSHION SHIELD
|
Remove in this Direction |
Disengage the claw and guide to remove the front LH seat lower cushion shield as shown in the illustration.
72266
36.REMOVE SEAT TRACK UPPER RAIL COVER
|
Remove in this Direction |
Disengage the 4 claws to remove the seat track upper rail cover as shown in the illustration.
Use the same procedure for both sides.
72125V
37.REMOVE REAR UPPER SEAT TRACK COVER
|
Remove in this Direction |
Disengage the 4 claws to remove the rear upper seat track cover as shown in the illustration.
Use the same procedure for both sides.
38.REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY
39.REMOVE POWER SEAT TILT MOTOR ASSEMBLY