Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
  1. Remove the 8 bolts and under cover.



4. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)
  1. Remove the 4 bolts and under cover.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.



6. LOOSEN FUEL TANK CAP ASSEMBLY


7. DRAIN FUEL


8. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



9. REMOVE TRANSMISSION ASSEMBLY
  1. for R151/R151F:
    Remove the transmission (Click here).

  1. for G50:
    Remove the transmission (Click here).



10. REMOVE BATTERY BRACKET


11. REMOVE BATTERY AND BATTERY TRAY


12. REMOVE AIR CLEANER ASSEMBLY
  1. for Ventilation Hose Type:
    Disconnect the ventilation hose.

  1. w/ Mass Air Flow Meter:
    Disconnect the mass air flow meter sensor connector.

  1. w/ Intake Air Temperature Sensor:
    Disconnect the intake air temperature sensor connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



13. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator (Click here).



14. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


15. DISCONNECT HOSES AND CONNECTORS


G035294E01
  1. Remove the engine room relay block cover (upper).

  1. Remove the No. 1 engine room relay block cover (side).

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.

  1. Disconnect the injector driver connectors.



    A226134
  1. for LHD:
    Disconnect the connectors.

    1. w/ A.D.D.
      Disconnect the 4WD control ECU connector.

    2. Disconnect the 4 ECU connectors.



    A149956
  1. for RHD:
    Disconnect the connectors.

    1. w/ A.D.D.
      Disconnect the 4WD control ECU connector.

    2. Disconnect the 4 ECU connectors.



    G035298E01
  1. Disconnect the 2 fuel hoses.

  1. Disconnect the vacuum pump hose.

  1. Disconnect the oil reservoir to pump hose.



    G034367E04
  1. Using a union nut wrench, disconnect the pressure feed tube.



16. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



17. REMOVE CLUTCH COVER ASSEMBLY


    D029616E01
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



18. REMOVE CLUTCH DISC ASSEMBLY

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



19. REMOVE FLYWHEEL SUB-ASSEMBLY


    A072851E02
  1. Using SST, hold the crankshaft.

    SST
    09213-58014  
    09330-00021  



    A114803
  1. Remove the 8 bolts and flywheel.



20. REMOVE REAR END PLATE
  1. Remove the bolt and end plate.



21. REMOVE ENGINE ASSEMBLY


    A098932E04
  1. Install a No. 1 engine hanger and No. 2 engine hanger to the locations shown in the illustration with 2 new bolts.

    HINT:
    Part No. 
    No. 1 Engine hanger
    w/ EGR cooler
    12284-30060
    Bolt (91512-61014)
    w/o EGR cooler
    12284-30020
    Bolt (91512-61014)
    No. 2 Engine hanger
    12282-67020
    Bolt (91642-81030)

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Install the engine hangers with new bolts.



    A098988E01
  1. Hold the engine with an engine sling device and chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



22. FIX ENGINE ON ENGINE STAND


23. REMOVE ENGINE WIRE
  1. Disconnect the engine wire from the engine.



24. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.



    A148169
  1. Remove the 6 bolts and timing belt cover.



25. REMOVE TIMING BELT


    A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.



    A070550E01
  1. Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.



  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.



26. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


27. REMOVE NO. 1 TIMING BELT TENSIONER ASSEMBLY


28. REMOVE CRANKSHAFT PULLEY


    A072413E02
  1. Using SST, remove the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A072414E02
  1. Using SST, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



29. REMOVE INTERCOOLER ASSEMBLY (w/ EGR Cooler)


    A149802
  1. Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.



    A135918
  1. Loosen the 2 clamps.



    A135919
  1. Remove the 4 bolts and intercooler.



30. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/ EGR Cooler)
  1. Remove the turbocharger (Click here).



31. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/o EGR Cooler)
  1. Remove the turbocharger (Click here).



32. REMOVE EXHAUST MANIFOLD


A149962E01
  1. w/o EGR Cooler:
    Remove the 8 nuts, 8 spacers and exhaust manifold as shown in the illustration.

  1. w/ EGR Cooler:
    Remove the 8 nuts, 8 spacers, 8 collars and exhaust manifold as shown in the illustration.



33. INSPECT EXHAUST MANIFOLD


A098949E01
  1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is greater than the maximum, replace the manifold.



34. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



35. REMOVE GENERATOR BRACKET
  1. Remove the bolt and bracket.



36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A098937E01
  1. Remove the 4 bolts and belt tensioner.



37. REMOVE INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)
  1. Remove the 2 bolts and support bracket.



38. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)
  1. Remove the 2 bolts and support bracket.



39. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Remove the 4 bolts and mounting bracket.



40. REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)


    I034100E02
  1. Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.



41. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
  1. Remove the 4 bolts and bracket.



42. REMOVE WATER INLET


A097637E01
  1. Remove the 3 bolts and water inlet.



43. REMOVE THERMOSTAT


44. REMOVE WATER OUTLET


    A149947E01
  1. Remove the 2 bolts and water outlet.



45. REMOVE GLOW PLUG ASSEMBLY
  1. w/ EGR Cooler:
    Remove the glow plug (Click here).

  1. w/ EGR System:
    Remove the glow plug (Click here).

  1. w/o EGR System:
    Remove the glow plug (Click here).



46. REMOVE MANIFOLD STAY (w/o EGR Cooler)


A099622E01
  1. Remove the 2 bolts and stay.



47. REMOVE OIL FILTER SUB-ASSEMBLY


B011502E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the drain oil container beneath the drain hose to collect the oil from the oil filter.



48. REMOVE INJECTION PIPE (w/o EGR Cooler)


A098967E07

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Remove the bolt and No. 2 injection pipe clamp.



  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



      A098893E01
    1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    2. A098968E07
    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



49. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/o EGR Cooler)


A098898E01
  1. Disconnect the 2 fuel hoses.

  1. Remove the check valve, 3 bolts, leakage pipe and gasket.



50. REMOVE INTAKE MANIFOLD (w/o EGR Cooler)


A131656
  1. Remove the 4 bolts, 2 nuts, manifold and gasket.



51. REMOVE INTAKE MANIFOLD (w/ EGR Cooler)
  1. Remove the intake manifold (Click here).



52. INSPECT INTAKE MANIFOLD


A098945E01
  1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is more than the maximum, replace the manifold.



53. REMOVE FUEL SUPPLY PUMP ASSEMBLY


G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.



    A098969E07
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley by using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



54. REMOVE COMMON RAIL ASSEMBLY


A098899E01
  1. Disconnect the fuel pressure sensor connector.

  1. Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the pressure limiter and pressure sensor.



55. REMOVE OIL COOLER COVER SUB-ASSEMBLY


A038741E01
  1. Disconnect the oil pressure switch connector and wire harness.

  1. Remove the 13 bolts, 2 nuts and oil cooler cover.



56. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)


    A148171
  1. Remove the bolt and gear cover insulator.



57. REMOVE VACUUM PUMP ASSEMBLY


A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



58. REMOVE VANE PUMP ASSEMBLY


A098935E01
  1. Remove the 2 nuts, vane pump and O-ring.



59. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and sensor.



60. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and sensor.



61. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Using a 17 mm deep socket wrench, remove the sensor.



62. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH


    A148168
  1. Remove the bolt and No. 2 cylinder block insulator.



    A098936E01
  1. Remove the 4 bolts and mounting bracket.



63. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and mounting bracket.