Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE CONSOLE BOX ASSEMBLY
(Click here)


4. REMOVE SHIFT LEVER BOOT ASSEMBLY


    C239519
  1. Remove the 4 screws and shift lever boot assembly.



5. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C213734
  1. Fold back the transfer front drive shift boot.

  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever.

    HINT:
    Move the transfer shift lever to the H4 position.



6. REMOVE NO. 1 ENGINE UNDER COVER


7. REMOVE NO. 2 ENGINE UNDER COVER


8. REMOVE NO. 3 ENGINE UNDER COVER


9. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front pipe from the exhaust manifold and remove the gasket.

  1. Remove the front pipe from the pipe support.



10. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


11. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


12. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



13. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C118024
  1. Remove the oil level dipstick.

  1. Remove the 2 bolts and transmission oil filler tube.

  1. Remove the O-ring from the transmission oil filler tube.



14. REMOVE STARTER ASSEMBLY
(Click here)


15. DISCONNECT OIL COOLER TUBE


    C118031
  1. Using a union nut wrench, disconnect the outlet oil cooler tube and inlet oil cooler tube.



    C118032
  1. Remove the 3 bolts and 3 clamps.



16. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C214917E01
  1. Remove the nut and clip, and disconnect the transmission control cable.



17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C213723
  1. Support the automatic transmission assembly with a transmission jack.



18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    G034256E02
  1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and No. 3 frame crossmember.



19. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


G034260E01
  1. Remove the 4 bolts and engine mounting insulator.



20. DISCONNECT WIRE HARNESS AND CONNECTOR


    C214940
  1. Remove the nut and disconnect the ground cable.



    C240769
  1. Remove the 2 bolts and heat insulator.



    C214924
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



  1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.


    C240745

  1. Disconnect the 8 wire harness clamps.



21. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
  1. Remove the flywheel housing dust seal.

  1. Turn the crankshaft to gain access to each bolt.



    C118033
  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter setting bolts.



22. REMOVE MANIFOLD STAY


    A252719
  1. Remove the 3 bolts and manifold stay.



23. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    C118035
  1. Remove the 7 bolts and automatic transmission assembly.

    NOTICE:
    Do not use excess force to pry off the transmission assembly.



24. REMOVE TRANSMISSION CONTROL CABLE BRACKET


G024484E01
  1. Remove the 2 bolts and control cable bracket from the transmission.



25. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.



26. REMOVE TORQUE CONVERTER ASSEMBLY
  1. Remove the torque converter from the automatic transmission assembly.