Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



3. REMOVE NO. 1 ENGINE UNDER COVER


4. REMOVE NO. 2 ENGINE UNDER COVER


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A099591
  1. Drain the coolant by removing the radiator reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug.


    A112147E03


    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Reservoir Cap
    *3
    Vent Plug
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -



7. DRAIN TRANSMISSION OIL
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



8. DRAIN POWER STEERING FLUID


9. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.



10. REMOVE BATTERY


11. REMOVE BATTERY TRAY


12. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



13. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A252793
  1. Remove the 3 bolts, 2 cap nuts and No. 1 engine cover.
    Text in Illustration 
    V100136
    Cap Nut



14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
(Click here)


15. REMOVE RADIATOR ASSEMBLY
(Click here)


16. REMOVE STARTER ASSEMBLY
(Click here)


17. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


18. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


19. DISCONNECT HEATER HOSE


    A236415
  1. Disconnect the 2 heater hoses.



20. DISCONNECT PRESSURE FEED TUBE ASSEMBLY


    A236416
  1. Disconnect the oil reservoir to pump hose.



    A236417
  1. Disconnect the pressure feed tube.



21. DISCONNECT FUEL HOSE


    A236418
  1. Disconnect the 2 fuel hoses.



22. DISCONNECT UNION TO CONNECTOR TUBE HOSE


    A236419
  1. Disconnect the union to connector tube hose.



23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
    Text in Illustration 
    *1
    Stopper



    B278059E01
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge



24. DISCONNECT WIRE HARNESS


A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A233020
  1. Remove the 2 nuts, detach the clamp and disconnect the wire harness.



    A233589
  1. Disconnect the 3 injector driver connectors.



    A219456
  1. Disconnect the turbo motor driver connector.

  1. Disconnect the 4 ECM connectors.



25. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



26. REMOVE MANUAL TRANSMISSION ASSEMBLY
(Click here)


27. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator.



28. REMOVE CLUTCH COVER ASSEMBLY


D029616E03
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



29. REMOVE CLUTCH DISC ASSEMBLY

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



30. REMOVE FLYWHEEL SUB-ASSEMBLY


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114803
  1. Remove the 8 bolts and flywheel.



31. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.



32. INSTALL ENGINE HANGERS


    A224109E01
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    NOTICE:
    Install the engine hangers with new bolts.

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30060 or 12284-30070
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030



33. REMOVE ENGINE ASSEMBLY


    A098988E01
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



34. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.



35. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.



36. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A233592E02
  1. Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *A
    RH Side
    *B
    LH Side



37. REMOVE NO. 1 TIMING BELT COVER


    A015094E01
  1. Remove the 6 bolts, 6 washers and timing belt cover.



38. REMOVE TIMING BELT


    A070549E05
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.



    A070550E01
  1. Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.



  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.



39. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.



40. REMOVE CRANKSHAFT PULLEY


    A251844E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A251845E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



41. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.



42. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 1 intercooler support bracket.



43. REMOVE NO. 2 IDLE PULLEY ASSEMBLY
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.



44. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



45. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



46. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



47. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



48. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)


49. REMOVE EXHAUST MANIFOLD


    A152664
  1. Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.

  1. Remove the gasket.



50. REMOVE WATER INLET


A250419
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and water inlet.

  1. Remove the bolt and wire harness clamp bracket from the water inlet.



51. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.



52. REMOVE WATER OUTLET


    A233596
  1. Remove the 2 bolts, water outlet and gasket.



53. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A220675
  1. Disconnect the 2 connectors.



    A211892
  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



54. REMOVE INTAKE MANIFOLD
(Click here)


55. REMOVE GLOW PLUG ASSEMBLY
(Click here)


56. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A098969E11
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side



57. REMOVE OIL FILTER SUB-ASSEMBLY


    A227248E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



58. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.



    A231856
  1. Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve or pressure sensor.



59. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    A231742
  1. Disconnect the 2 fuel hoses.



    A231743
  1. Disconnect the fuel temperature sensor connector and suction control valve connector.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E04
  1. Remove the set nut and O-ring while holding the crankshaft pulley using SST.

    SST
    09213-58014  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E02
  1. Using SST, disconnect the fuel supply pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and fuel supply pump.

    NOTICE:
    1. Do not hold or carry the fuel supply pump by the pipe.
    2. The fuel supply pump must be kept horizontal.

  1. Remove the O-ring.



60. REMOVE OIL COOLER COVER SUB-ASSEMBLY
  1. Disconnect the oil pressure switch connector.

  1. Remove the 2 nuts and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.



    A038741E01
  1. Remove the 13 bolts, oil cooler cover and gasket.



61. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



62. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



63. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.



  1. Detach the 4 clips and remove the bolt and crankshaft position sensor.


    A253484



64. REMOVE CAMSHAFT POSITION SENSOR


    A135909
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.



65. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A252686
  1. Disconnect the engine coolant temperature sensor connector.

  1. Remove the engine coolant temperature sensor.

  1. Remove the gasket from the engine coolant temperature sensor.



66. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A233593E02
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.
    Text in Illustration 
    *A
    RH Side
    *B
    LH Side



67. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.