DTC P0088 Fuel Rail / System Pressure - Too High |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds | The fuel pressure of the common rail exceeds 200000 kPa (2039 kgf/cm2, 29000 psi) (1 trip detection logic). |
|
| DTC No. | Data List |
| P0088 |
|
| Engine Speed | Fuel Press |
| Idling | Approximately 25000 to 35000 kPa |
| 3000 rpm (No engine load) | Approximately 50000 to 70000 kPa |

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| Result | Proceed to |
| P0088 is output | A |
| P0088 and "P0190, P0192 and/or P0193" are output | B |
|
| ||||
| A | |
| 2.CHECK FREEZE FRAME DATA (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Record the stored DTCs and freeze frame data.
| Result | Proceed to |
| Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data | B |
| Except above | A |
|
| ||||
| A | |
| 3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
![]() |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


| Tester Connection | Condition | Specified Condition |
| E7-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| *a | Component with harness connected (ECM) |
| Result | Proceed to |
| MIL comes on or noise present in the waveform | B |
| Except above | A |
|
| ||||
| A | |
| 4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE) |
Replace the fuel supply pump assembly (Click here).
| NEXT | |
| 5.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 6.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 7.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0088.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
| Pending DTC | P0088 is output | A |
| All Readiness | NORMAL | B |
| ABNORMAL | A |
|
| ||||
| A | |
| 8.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
![]() |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
| E7-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| *a | Component with harness connected (ECM) |
| Result | Proceed to |
| MIL comes on or noise present in the waveform | A |
| Except above | B |
|
| ||||
| A | |
| 11.REPLACE COMMON RAIL ASSEMBLY |
Replace the common rail assembly (Click here).
| NEXT | |
| 12.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| NEXT | ||
| ||