Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Check CAN Bus Line for Short to GND


DESCRIPTION

There may be a short circuit between the CAN bus line and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 1 Ω.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 1 Ω.
  1. Short to GND
  2. Brake actuator assembly (skid control ECU)
  3. Spiral cable (steering angle sensor)
  4. Yaw rate sensor
  5. ECM
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM


C234151E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with SRS:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    H102621E35
  1. Disconnect the J51 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    D3-14 (CANL) - D3-4 (CG)
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    D3-14 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the J51 No. 3 junction connector connector.


NEXT


4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    H102621E35
  1. Disconnect the J57 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    D3-14 (CANL) - D3-4 (CG)
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    D3-14 (CANL) - D3-4 (CG)



NG
Go to step 9
OK


5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C190790E16
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J57-13 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J57-7 (CANL) - D3-4 (CG)
    J57-13 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J57-7 (CANL) - D3-4 (CG)



NG
Go to step 7
OK


6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C190790E17
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J57-12 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J57-6 (CANL) - D3-4 (CG)
    J57-12 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J57-6 (CANL) - D3-4 (CG)



NG
Go to step 8
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)


    C190790E16
  1. Disconnect the S25 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J57-13 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J57-7 (CANL) - D3-4 (CG)
    J57-13 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J57-7 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    C190790E17
  1. Disconnect the E5*1 or E13*2 ECM connector.

    1. *1: for 1KD-FTV, 2KD-FTV
    2. *2: for 1GR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    Proceed to
    J57-12 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK (for 1KD-FTV)
    A
    OK (for 2KD-FTV)
    B
    J57-6 (CANL) - D3-4 (CG)
    OK (for 1GR-FE)
    C
    J57-12 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    D
    J57-6 (CANL) - D3-4 (CG)



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C190791E16
  1. Disconnect the J56 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J56-1 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J56-2 (CANL) - D3-4 (CG)
    J56-1 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J56-2 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


10.CONNECT CONNECTOR
  1. Reconnect the J57 No. 1 junction connector connector.


NEXT


11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    H102621E35
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    D3-14 (CANL) - D3-4 (CG)
    D3-6 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    D3-14 (CANL) - D3-4 (CG)



NG
Go to step 14
OK


12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)


    C190791E17
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J56-4 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J56-6 (CANL) - D3-4 (CG)
    J56-4 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J56-6 (CANL) - D3-4 (CG)



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR)


    C190791E17
  1. Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J56-4 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J56-6 (CANL) - D3-4 (CG)
    J56-4 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J56-6 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR (Click here)  

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190792E16
  1. Disconnect the J52 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J52-2 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J52-1 (CANL) - D3-4 (CG)
    J52-2 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J52-1 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


15.CONNECT CONNECTOR
  1. Reconnect the J56 No. 2 junction connector connector.

  1. Reconnect the J52 No. 3 junction connector connector.


NEXT


16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C190792E17
  1. Disconnect the J53 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J53-2 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J53-1 (CANL) - D3-4 (CG)
    J53-2 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J53-1 (CANL) - D3-4 (CG)



NG
Go to step 17
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C190792E17
  1. Disconnect the S23 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J53-2 (CANH) - D3-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    J53-1 (CANL) - D3-4 (CG)
    J53-2 (CANH) - D3-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    J53-1 (CANL) - D3-4 (CG)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (Click here)