DTC C1415 Rear Speed Sensor RH Output Malfunction |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1416 Rear Speed Sensor LH Output Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1415 C1416 | One of the following conditions is met:
|
|
| C1277 C1278 | Stored during Test Mode. |
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | Rear speed sensor RH open circuit detection / Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection / Error or Normal | Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
Check the speed value output from the speed sensor displayed on the intelligent tester.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the signal check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation (Click here).
| *1 | Rear Speed Sensor |
| *a | No clearance |
| *b | CORRECT |
| *c | INCORRECT |
|
| ||||
| OK | |
| 6.INSPECT REAR SPEED SENSOR TIP |
Turn the ignition switch off.
Remove the rear speed sensor (Click here).
Check the rear speed sensor tip.
|
| ||||
| OK | |
| 7.INSPECT REAR SKID CONTROL ROTOR |
Turn the ignition switch off.
Remove the rear axle shaft with backing plate (Click here).
Check the rear skid control rotor.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-17 (RR+) - S20-2 (RR+) | Always | Below 1 Ω |
| S25-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| S25-16 (RR-) - S20-1 (RR-) | Always | Below 1 Ω |
| S25-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S25-5 (RL+) - S19-2 (RL+) | Always | Below 1 Ω |
| S25-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| S25-4 (RL-) - S19-1 (RL-) | Always | Below 1 Ω |
| S25-4 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK TERMINAL VOLTAGE (SENSOR POWER SUPPLY VOLTAGE TERMINAL) |
Turn the ignition switch off.
Connect the skid control ECU (brake actuator assembly) connector.
Disconnect the rear speed sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S20-2 (RR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S19-2 (RL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Rear Speed Sensor) |
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 11.REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||