DTC B15C3 Speaker Output Short |
| DTC No. | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit. |
|

| 1.CHECK FOR DTC |
Disconnect the R26 and R25 radio and display receiver assembly connectors.
Clear the DTCs (Click here).
Check if DTC B15C3 is output (Click here).
|
| ||||
| OK | |
| 2.CHECK FOR DTC |
Reconnect the R25 radio and display receiver assembly connector.
Clear the DTC (Click here).
Check if DTC B15C3 is output (Click here).
| Result | Proceed to |
| Malfunction in front speaker area | A |
| Malfunction in rear speaker area | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
Disconnect the R25 radio and display receiver assembly connector.
Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R25-1 (FR+) - T25-4 | Always | Below 1 Ω |
| R25-5 (FR-) - T25-2 | Always | Below 1 Ω |
| R25-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| R25-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| R25-2 (FL+) - T24-4 | Always | Below 1 Ω |
| R25-6 (FL-) - T24-2 | Always | Below 1 Ω |
| R25-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| R25-6 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.
Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T25-3 - S16-1 | Always | Below 1 Ω |
| T25-1 - S16-2 | Always | Below 1 Ω |
| T25-3 - Body ground | Always | 10 kΩ or higher |
| T25-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T24-3 - S15-1 | Always | Below 1 Ω |
| T24-1 - S15-2 | Always | Below 1 Ω |
| T24-3 - Body ground | Always | 10 kΩ or higher |
| T24-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here).
|
| ||||
| OK | |
| 6.CHECK FRONT NO. 2 SPEAKER ASSEMBLY |
Replace the front No. 2 speaker with a known good one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the R26 radio and display receiver assembly connector.
Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R26-1 (RR+) - S18-1 | Always | Below 1 Ω |
| R26-3 (RR-) - S18-2 | Always | Below 1 Ω |
| R26-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| R26-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| R26-2 (RL+) - S17-1 | Always | Below 1 Ω |
| R26-6 (RL-) - S17-2 | Always | Below 1 Ω |
| R26-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| R26-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here)
Inspect the rear speaker assembly (Click here).
|
| ||||
| OK | ||
| ||