INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
- Use the same procedure for RHD and LHD vehicles.
| 1. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
for LHD:
Attach the 5 guides and 8 claws to install the upper instrument panel.
Install the 2 bolts <A> and 2 screws <B>.


Text in Illustration *A
w/o Front Passenger Airbag
*B
w/ Front Passenger Airbag
*1
Bolt <A>
*2
Screw <B>
for RHD:
Attach the 5 guides and 8 claws to install the upper instrument panel.
Install the 2 bolts <A> and 2 screws <B>.


Text in Illustration *A
w/o Front Passenger Airbag
*B
w/ Front Passenger Airbag
*1
Bolt <A>
*2
Screw <B>
| 2. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the protective cover.
Attach the 2 guides and 2 clips to install the front pillar garnish.
Install the front door opening trim.
| 3. INSTALL FRONT PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 4. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip) |
- HINT:
- Use the same procedure for both front assist grips sub-assemblies.
Install the front assist grip sub-assembly with the 2 screws.
| 5. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip) |
- HINT:
- Use the same procedure for both assist grip plugs LH.
Attach the 2 claws to install the assist grip plug LH.
| 6. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip) |
- HINT:
- Use the same procedure described for the LH side.
| 7. INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag) |
![]() ![]() |
Attach the 12 claws to install the airbag.
Attach the clamp to the bracket.
Tighten the 2 bolts.

- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Connect the connector to the airbag.

- NOTICE:
- When handling the airbag connector, do not damage the airbag wire harness.
| 8. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (w/ Front Passenger Airbag) |
![]() ![]() |
Attach the 2 hinges to install the glove compartment door.
Text in Illustration *1
Hinge
While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.

Text in Illustration *1
Stopper
| 9. INSTALL RADIO TUNER OPENING COVER (w/o Audio) |
Install the radio tuner opening cover with the 4 screws.
| 10. INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio) |
for Radio Receiver Type:
(Click here)
for Radio and Display Type:
(Click here)
| 11. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
for Manual Air Conditioning System:
Connect the connectors.
Attach the 4 claws to connect the air conditioner control.
Attach the 10 claws and 4 clips to install the center instrument cluster finish panel.
for Automatic Air Conditioning System:
Connect the connectors.
Attach the 8 claws and 4 clips to install the center instrument cluster finish panel.
| 12. INSTALL COMBINATION METER ASSEMBLY |
Connect the connectors and attach the clamp.
Install the combination meter with the 3 screws.
| 13. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
Attach the 2 claws and 3 guides to install the No. 1 instrument cluster finish panel.
Install the clip <C>.
| 14. INSTALL STEERING WHEEL ASSEMBLY |
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System) |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 16. CHECK SRS WARNING LIGHT (w/ Airbag System) |


