2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. TABLE OF BOLT, SCREW AND NUT

B277605E01
  1. All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabetical code in the table.


2. PRECAUTION (w/ Airbag System)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE STEERING WHEEL ASSEMBLY
(Click here)

5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL

B278228
  1. Remove the clip <C>.

  1. Detach the 2 claws and 3 guides and remove the No. 1 instrument cluster finish panel.


6. REMOVE COMBINATION METER ASSEMBLY

B278372
  1. Remove the 3 screws.

  1. Disconnect the connectors, detach the clamp and remove the combination meter.


7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. for Manual Air Conditioning System:

    1. B278367E01
      Put protective tape around the center instrument cluster finish panel.
      Text in Illustration 
      *1
      Protective Tape

    2. Using a moulding remover, detach the 10 claws and 4 clips.

    3. B278366
      Detach the 4 claws and disconnect the air conditioner control.

    4. Disconnect the connectors and remove the center instrument cluster finish panel.

  1. for Automatic Air Conditioning System:

    1. B278368E01
      Put protective tape around the center instrument cluster finish panel.
      Text in Illustration 
      *1
      Protective Tape

    2. Using a moulding remover, detach the 8 claws and 4 clips.

    3. Disconnect the connectors and remove the center instrument cluster finish panel.


8. REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)
  1. for Radio Receiver Type:
    (Click here)

  1. for Radio and Display Type:
    (Click here)


9. REMOVE RADIO TUNER OPENING COVER (w/o Audio)

B278057
  1. Remove the 4 screws and radio tuner opening cover.


10. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (w/ Front Passenger Airbag)

B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    Text in Illustration 
    *1
    Stopper

  1. B278059E01
    Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge


11. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)

B112127E01
  1. Disconnect the connector from the airbag.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. B112126
    Remove the 2 bolts.

  1. Detach the clamp from the bracket.

  1. B112264E01
    Detach the 12 claws and remove the airbag.


12. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)

B277720E01

HINT:
Use the same procedure for both front No. 1 assist grip plugs.

  1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


13. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)

HINT:
Use the same procedure described for the LH side.


14. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

B206335

HINT:
Use the same procedure for both front assist grips.

  1. Remove the 2 screws and front assist grip.


15. REMOVE FRONT PILLAR GARNISH LH

B276932
  1. Remove the part of the front door opening trim attached to the front pillar garnish.

  1. Detach the 2 clips and 2 guides and remove the front pillar garnish.

  1. w/ Curtain Shield Airbag:
    Protect the curtain shield airbag assembly.

    1. B289825E01
      Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

      Text in Illustration 
      *1
      Protective Cover
      *2
      Adhesive Tape


16. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


17. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

  1. for LHD:

    1. Put protective tape around the upper instrument panel.

    2. Remove the 2 bolts <A> and 2 screws <B>.

    3. Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.

      HINT:
      Tape the screwdriver tip before use.


      B277541E01
      Text in Illustration 
      *A
      w/o Front Passenger Airbag
      *B
      w/ Front Passenger Airbag
      *1
      Protective Tape
      *2
      Bolt <A>
      *3
      Screw <B>
      -
      -

  1. for RHD:

    1. Put protective tape around the upper instrument panel.

    2. Remove the 2 bolts <A> and 2 screws <B>.

    3. Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.

      HINT:
      Tape the screwdriver tip before use.


      B277371E01
      Text in Illustration 
      *A
      w/o Front Passenger Airbag
      *B
      w/ Front Passenger Airbag
      *1
      Protective Tape
      *2
      Bolt <A>
      *3
      Screw <B>
      -
      -

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →