2014 Hilux · Service Manual ENGINE

Rough Idling or Excessive Engine Vibrations

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Malfunction Condition
Main Trouble Area
Related Trouble Area
  1. Rough idling or juddering due to abnormal combustion
  2. Juddering when vehicle is starting due to clutch system malfunctions
  1. Injector malfunctions
    1. Injector sliding malfunction
    2. Injector stuck closed
    3. Injector stuck open
    4. Deposits in injector
    5. Injector circuit malfunction
  2. Clutch system malfunctions
    1. Clutch system (juddering when starting)
  1. Injector compensation code
  2. Fuel leak
  3. Engine mounting
  4. Intake air system leakage
  5. Intake air system blockage
  6. EGR system
  7. Throttle valve system
  8. Mass air flow meter
  9. Supply pump
  10. Fuel pressure sensor
  11. EDU (P0200 set simultaneously)
  12. Low quality fuel
  13. Vehicle modifications
  14. Fuel filter air bleed problem
  15. Accessory problem (A/C, generator, etc.)
  16. ECM

HINT:
  1. This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.
  2. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
  3. Check that the vehicle has not been modified in any way prior to the vehicle inspection.


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Mass Air Flow Meter 
    Main fault
    Decrease in performance (foreign matter is stuck)
    Symptoms
    Lack of power, black smoke
    Data List
    MAF

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.

    Glow System 
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug
    Engine 
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.

  2. Diesel Injection

    Fuel Supply Pump 
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
    Fuel Filter 
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
    Fuel Injector 
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is more than 70°C (158°F)).
    Injector Driver (EDU) 
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.
    Fuel Pressure Sensor 
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (however, the value may not deviate even when a malfunction is present).
    Diagnostic Trouble Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.
    Irregular Fuel 
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Main fault
    1. Does not move smoothly
    2. Does not close completely
    Symptoms
    1. Rough idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
    Data List
    Actual EGR Valve Pos., Target EGR Pos.
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine is warmed up.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.
    2. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position
      0%: Fully open
      100%: Fully closed
    2. When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Rough Idling or Excessive Engine Vibrations
  1. Engine Speed
  2. MAF
  3. Intake Air
  4. Coolant Temp
  5. Engine Speed of Cyl #1 (to #4)
  6. Target Common Rail Pressure
  7. Fuel Press
  8. Target Pump SCV Current
  9. Injection Feedback Val #1 (to #4)
  10. Injection Volume
  11. Actual Throttle Position
  12. Target EGR Position
  13. Actual EGR Valve Pos.
  14. EGR Close Lrn. Status
  15. EGR Close Lrn. Val.

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing a fuel injector, the ECM needs registration (Click here).


1. CHECK MALFUNCTION CONDITION
  1. Identify when shuddering occurs.

    Result 
    Result
    Proceed to
    When idling
    A
    When engaging engine clutch at vehicle start
    B
    (Clutch system shudders)



B
REPAIR OR REPLACE CLUTCH SYSTEM
A


2. CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
  1. Check the wire harness and connector connections of common rail system components.

    OK:
    The wire harnesses and connectors are connected securely.

    HINT:
    The engine may have problems when there is an intermittent disconnection in a circuit related to the fuel pressure sensor, crankshaft position sensor, engine coolant temperature sensor, etc.



NG
Go to step 15
OK


3. READ OUTPUT DTC (RELATING TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.

Result 
Result
Proceed to
No DTCs are output
A
Engine related DTCs are output
B


B
GO TO DTC CHART
A


4. TAKE SNAPSHOT DURING IDLING (PROCEDURE 4)

  1. A176220E02
    Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine (engine coolant temperature is 70°C (158°F) or higher)

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  1. Take a snapshot when idling with no load after the engine is warmed up.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
    2. Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
    3. The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
    4. If rough idling occurs when the A/C switch is on, take another snapshot with the A/C switch on.


NEXT


5. CHECK WHITE SMOKE
  1. Start the engine.

  1. Fully depress the accelerator pedal and then release it.

  1. Check whether the white smoke is emitted when racing the engine.

    NOTICE:
    Be sure not to check for white smoke indoors.

    HINT:
    Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells like burning oil.

    Result 
    Result
    Proceed to
    White smoke is emitted
    B
    White smoke is not emitted
    A



B
Go to step 16
A


6. CHECK DATA LIST (ENGINE SPEED)
  1. Check engine speed in the snapshot taken at procedure 4 when the engine was idling.

    Result 
    Result
    Proceed to
    Change in engine speed coincides with air conditioning system operation
    B
    Except above
    A



B
Go to step 17
A


7. CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
  1. Check Injection Feedback Val # in the snapshot taken at procedure 4 when the engine was idling.

    Result 
    Result
    Proceed to
    Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large
    A
    Except above
    B

    HINT:
    1. When there is a problem with the operation of a fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
    2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the fuel injectors are not malfunctioning.



B
Go to step 18
A


8. INSPECT INJECTOR COMPENSATION CODE
  1. Read the injector compensation code (Click here).

    OK:
    Compensation codes stored in the ECM match compensation codes of the installed fuel injectors.



NG
Go to step 14
OK


9. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
  1. Clean the fuel filter case and replace the fuel filter.

    HINT:
    Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.


NEXT


10. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


11. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

    HINT:
    1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.
    2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


12. REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
  1. Replace the fuel injector of the malfunctioning cylinder (Click here).


NEXT


13. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


14. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation code (Click here).

  1. Perform the fuel injector pilot quantity learning (Click here).



NEXT
Go to step 30
15. REPAIR OR REPLACE HARNESS AND CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 30
16. CHECK AND REPAIR ENGINE ASSEMBLY
  1. Check the following items, and repair the malfunctioning part if necessary.

    1. Check cylinder compression pressure (Click here).

    2. Inspect the glow plug assembly (Click here).



NEXT
Go to step 18
17. CHECK AIR CONDITIONING SYSTEM
  1. Check the air conditioning system.



NEXT
Go to step 30
18. CHECK DATA LIST (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
  1. Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was idling.

    Result 
    Result
    Proceed to
    Fuel Press is outside range of +/-5000 kPa from Target Common Rail Pressure
    A
    Except above
    B



B
Go to step 27
A


19. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
A099839E13
  1. Disconnect the S8 suction control valve connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    S8-1 - PCV+ (E8-2)
    Always
    Below 1 Ω
    S8-2 - PCV- (E8-1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    S8-1 or PCV+ (E8-2) - Body ground
    Always
    10 kΩ or higher
    S8-2 or PCV- (E8-1) - Body ground
    Always
    10 kΩ or higher

    HINT:
    When there is an open circuit, Target Pump SCV Current is outside the range of 923 to 1123 mA.



NG
Go to step 24
OK


20. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When there is a lack of fuel, the fuel pressure drops.
    2. Inspect for fuel filter clogging.



NG
Go to step 25
OK


21. REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


22. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


23. PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).



NEXT
Go to step 30
24. REPAIR OR REPLACE HARNESS AND CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 30
25. CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and repair or replace the clogged fuel pipe.


NEXT


26. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).



NEXT
Go to step 30
27. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up (engine coolant temperature is 70°C (158°F) or higher), and the A/C switch and all accessory switches should be off.

  1. Turn the ignition switch off. Wait for 30 seconds and then restart the engine.

  1. Turn the tester on.

  1. Select the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the MAF value displayed on the tester when engine idling.

  1. Select the following menus: Powertrain / Engine and ECT / Active Test / Activate The EGR Valve Close.

  1. Read the MAF value when the EGR valve is closed using the Active Test function.

    HINT:
    1. If idling continues for 15 minutes or more, the EGR valve opening angle target becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to run the vehicle or to restart the engine.
    2. Before performing the diagnosis, confirm that the EGR valve opening angle target value is not 0%.

    Result:
    Active Test
    Result
    Proceed to
    Activate The EGR Valve Close:
    off (Open) to on (Close)
    MAF value is not changed
    A
    MAF value is changed
    B

    NOTICE:
    As the numerical values shown below may differ depending on the conditions such as the differences of measuring environments, and the changes of vehicle condition due to aging, do not determine with these values whether acceptable of not.

    HINT:
    The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly, electric EGR control valve assembly or mass air flow meter.

    Reference:
    EGR Valve Condition (Opening)
    MAF (Reference)
    Measuring Condition
    Open
    3.0 to 9.0 gm/s
    1. Atmosphere pressure: 101 kPa
    2. Intake air temperature: 30°C (86°F)
    3. Engine coolant temperature: 88°C (190°F)
    Close
    15 to 22 gm/s



B
Go to step 29
A


28. REMOVE DEPOSIT (EGR VALVE ASSEMBLY)
  1. Remove the EGR valve assembly.

  1. Visually check the EGR valve assembly for deposits.If there are deposits, clean the EGR valve assembly.

    NOTICE:
    1. When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
    2. Do not forcibly open the valve, as it may be damaged or deformed.
    3. When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

    HINT:
    1. If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.
    2. If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.
    3. If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the EGR valve.
    4. When cleaning the EGR valve assembly, use a piece of cloth soaked with non-residue solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.



NEXT
Go to step 30
29. CHECK AND REPLACE ENGINE MOUNTING INSULATOR
  1. Check the following items, and repair or replace the malfunctioning part if necessary.

    1. Check that the engine mounting insulators are installed correctly.

    2. Check that the engine mounting insulators are not twisted.

    3. Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.


NEXT


30. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END


← Rough Idling or Excessive Engine Vibrations (Aug 2012 – Jul 2013)Rough Idling or Excessive Engine Vibrations (from Aug 2014) →