C1401 Front Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1402 Front Speed Sensor LH Malfunction
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). The speed sensor has a magnet behind its detection terminal, and detects changes in magnetic flux density between the peaks and valleys of the magnetic rotor teeth.The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU (brake actuator assembly). The ECU monitors the wheel speeds through these pulse signals to control the brake control system.
- HINT:
- When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1401 C1402 |
One of the following conditions is met:
|
|
| C1271 C1272 |
Stored during Test Mode. |
|
- HINT:
- DTCs C1401 and C1271 are for the front speed sensor RH.
- DTCs C1402 and C1272 are for the front speed sensor LH.
- DTCs C1401 and C1271 are for the front speed sensor RH.
INSPECTION PROCEDURE
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
| 1. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

Text in Illustration *1
Front Speed Sensor
*a
No clearance
*b
CORRECT
*c
INCORRECT
- OK:
- There is no clearance between the sensor and the steering knuckle.
- The installation bolt is tightened properly.
|
|
||||
| OK | |
| 2. INSPECT FRONT SPEED SENSOR TIP |
Turn the ignition switch off.
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil or foreign matter on the sensor tip.
- NOTICE:
- Do not replace the speed sensor if no damage to the speed sensor tip is found.
- HINT:
- If the sensor is contaminated with oil or other foreign material, clean the sensor.
- If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.
- If the sensor is contaminated with oil or other foreign material, clean the sensor.
|
|
||||
| OK | |
| 3. INSPECT FRONT SKID CONTROL ROTOR |
Turn the ignition switch off.
Remove the front skid control rotor (Click here).
Check the front skid control rotor.
- OK:
- No scratches, oil or foreign matter on the rotor.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check the speed value output from the speed sensor displayed on the intelligent tester.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | ||
| ||
| 5. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
