2014 Hilux · Service Manual BRAKE

C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction

Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012

Also covers:

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.
DTC Code
DTC Detection Condition
Trouble Area
C1430
Either condition is met:
  1. With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.
  2. With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.
  1. Brake pedal load sensing switch (Brake with switch pedal sub-assembly)
  2. Brake pedal load sensing switch circuit
  3. Skid control ECU (Brake actuator assembly)
  4. Brake pedal height and stop light switch installation
  5. Brake with switch pedal sub-assembly
C1431
Either condition is met:
  1. Immediately after the ignition switch is turned to ON, the brake pedal load sensing switch is on and the stop light switch is off for 10 seconds or more.
  2. The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (18 mph) occurs 5 times in succession.

WIRING DIAGRAM

Refer to DTC C1429 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

HINT:
When DTC C1425 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond specified point
    OFF: Brake pedal not depressed beyond specified point
    -

  1. Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.

  1. Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.

    OK:
    The stop light switch turns on first, and then the brake pedal load sensing switch turns on.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Turning on of brake pedal load sensing switch is not confirmed)
    B
    NG (Brake pedal load sensing switch turns on first)
    C



B
Go to step 3

C
Go to step 5
A


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C190633E02
Text in Illustration  
*1
Brake Pedal Load Sensing Switch
*2
Brake with Switch Pedal Sub-assembly
*a
Component without harness connected
(Brake Pedal Load Sensing Switch)
*b
Brake Pedal Released (Closed)
*c
Brake Pedal Depressed (Open)
-
-

NOTICE:
  1. Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
  2. When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.

  1. Turn the ignition switch off.

  1. Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 1
    Brake pedal depressed
    950 to 1050 Ω
    Brake pedal released
    203 to 223 Ω



NG
REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-27 (FSW+) - B8-2
    Always
    Below 1 Ω
    S35-27 (FSW+) - Body ground
    Always
    10 kΩ or higher
    B8-1 - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Click here).

    OK:
    The brake pedal height and stop light switch installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY (Click here)


← C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction (+ C1431) (Jun 2011 – Oct 2011)C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction (+ C1431) (Apr 2012 – Jul 2012) →