C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1430 |
Either condition is met:
|
|
| C1431 |
Either condition is met:
|
WIRING DIAGRAM
Refer to DTC C1429 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
- HINT:
- When DTC C1425 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.
- OK:
- The stop light switch turns on first, and then the brake pedal load sensing switch turns on.
Result Result
Proceed to
OK
A
NG (Turning on of brake pedal load sensing switch is not confirmed)
B
NG (Brake pedal load sensing switch turns on first)
C
|
|
||||
|
|
||||
| A | |
| 2. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH |


| *1 |
Brake Pedal Load Sensing Switch |
*2 |
Brake with Switch Pedal Sub-assembly |
| *a |
Component without harness connected (Brake Pedal Load Sensing Switch) |
*b |
Brake Pedal Released (Closed) |
| *c |
Brake Pedal Depressed (Open) |
- |
- |
- NOTICE:
- Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
- When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.
- Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
Turn the ignition switch off.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2 - 1
Brake pedal depressed
950 to 1050 Ω
Brake pedal released
203 to 223 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-27 (FSW+) - B8-2
Always
Below 1 Ω
S35-27 (FSW+) - Body ground
Always
10 kΩ or higher
B8-1 - Body ground
Always
Below 1 Ω
Result Result
Proceed to
NG
A
OK
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
|
|
||||
| OK | ||
| ||
