2014 Hilux · Service Manual ENGINE

P0100 Mass Air Flow Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The Mass Air Flow (MAF) meter measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air-fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air.
By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the air flow through the sensor. The ECM interprets this voltage as the intake air amount.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the set temperature.
A080089E02
DTC No.
DTC Detection Condition
Trouble Area
P0100
When MAF meter circuit has open or short for more than 3 seconds under 2,000 rpm engine speed
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0102
When MAF meter circuit has open for more than 3 seconds under 2,000 rpm engine speed
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0103
When MAF meter circuit has short for more than 3 seconds under 2,000 rpm engine speed
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM

HINT:
When DTC P0100, P0102 or P0103 is detected, check the air-flow ratio by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / MAF.
Air Flow Rate (gm/s)
Malfunction
Approximately 0.0
  1. Open in MAF meter power source circuit
  2. Open or short in VG circuit
167.5 or more
Open in EVG circuit


WIRING DIAGRAM

A154843E06

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / MAF.

  1. Read the values.

    Result:
    Air flow rate (gm/s)
    Proceed to
    Approximately 0.0
    A
    167.5 or more
    B
    Between 1 and 167.4*
    C

    HINT:
    *: The value must change when the throttle valve is opened or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. CHECK MASS AIR FLOW METER (POWER SOURCE CIRCUIT)

  1. A084809E05
    Disconnect the A4 MAF meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminal of the wire harness side connector and the body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    A4-1 (+B) - Body ground
    11 to 14 V



NG
Go to step 5
OK


3. CHECK ECM (VG VOLTAGE)

  1. A119979E43
    Start the engine.

  1. Measure the voltage of E7 the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-24 (VG) - E7-32 (EVG)
    Engine idling
    0.5 to 3.4 V

    HINT:
    The A/C switch should be turned OFF.



OK
REPLACE ECM
NG


4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A096607E03
    Disconnect the A4 MAF meter connector.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A4-3 (VG) - E7-24 (VG)
    Below 1 Ω
    A4-2 (E2G) - E7-32 (EVG)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A4-3 (VG) or E7-24 (VG) - Body ground
    10 kΩ or higher
    A4-2 (E2G) or E7-32 (EVG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER

5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY (MAIN RELAY))
G034942E07
  1. Disconnect the A4 MAF meter connector.

  1. Remove the No. 1 integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J No. 1 integration relay connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A4-1 (+B) - 1J-5
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A4-1 (+B) or 1J-5 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT

6. CHECK ECM (SENSOR GROUND)
A119979E44
  1. Measure the resistance of the E7 ECM connector and body ground.

    Standard resistance:
    Tester Connection
    Specified Condition
    E7-32 (EVG) - Body ground
    Below 1 Ω



NG
REPLACE ECM
OK


7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER- ECM)
A096607E03
  1. Disconnect the A4 MAF meter connector.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A4-3 (VG) - E7-24 (VG)
    Below 1 Ω
    A4-2 (E2G) - E7-32 (EVG)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A4-3 (VG) or E7-24 (VG) - Body ground
    10 kΩ or higher
    A4-2 (E2G) or E7-32 (EVG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER


← P0100 Mass Air Flow Circuit Malfunction (+ P0102, P0103) (Aug 2013 – Jul 2014)P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (Jun 2011 – Jul 2012) →