2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. G038856E01
    Disconnect the fuel pump connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/25 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump connector.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE ENGINE ASSEMBLY
  1. Remove the engine from the vehicle (Click here).


4. REMOVE DRIVE PLATE AND RING GEAR ASSEMBLY (for Automatic Transmission)

A076326E08
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A076327E01
    Remove the 8 bolts, rear spacer, drive plate and front spacer.

    NOTICE:
    Do not reuse the bolts.


5. REMOVE FLYWHEEL (for Manual Transmission)

A076326E08
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A076899E01
    Remove the 8 bolts and flywheel.

    NOTICE:
    Do not reuse the bolts.


6. INSTALL ENGINE ASSEMBLY TO STAND

7. REMOVE OIL DIPSTICK GUIDE
  1. Remove the oil dipstick gauge.

  1. Remove the bolt and oil dipstick guide.

  1. Remove the O-ring from the oil dipstick guide.


8. REMOVE WATER INLET

  1. A112082
    Remove the 3 nuts, water inlet with thermostat and gasket.


9. REMOVE GENERATOR

A122806
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


10. REMOVE V-RIBBED BELT TENSIONER

A076445E01
  1. Remove the 5 bolts and V-ribbed belt tensioner.


11. REMOVE NO. 2 IDLER PULLEY

NOTICE:
Use the same procedure for both No. 2 idler pulleys.

  1. w/ Idler Pulley Cover Plate:

    1. A191314E01
      Remove the bolt, No. 2 idler pulley cover plate, idler pulley and idler pulley cover plate.

  1. w/o Idler Pulley Cover Plate:

    1. A191315E01
      Remove the bolt, No. 2 idler pulley cover plate and idler pulley.

  1. A076338E01
    for Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


12. REMOVE NO. 1 IDLER PULLEY
  1. Remove the bolt and idler pulley.


13. REMOVE CRANKSHAFT PULLEY

  1. A072945E01
    Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover.

  1. G038065E03
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.

  1. A072947E01
    Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)


14. REMOVE NO. 2 OIL PAN

  1. A112956E01
    Remove the 14 bolts and 2 nuts.

  1. A112957
    Insert the blade of an oil pan seal cutter between the oil pan and No. 2 oil pan, cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the oil pan and No. 2 oil pan.
    2. Be careful not to damage the No. 2 oil pan flange.


15. REMOVE OIL STRAINER

  1. A112955
    Remove the bolt, 2 nuts, oil strainer and gasket.


16. REMOVE NO. 1 OIL PAN

  1. A112952E02
    Remove the 17 bolts and 2 nuts.

  1. A112954
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.


17. REMOVE IGNITION COIL

18. REMOVE CYLINDER HEAD COVER RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, head cover and gasket.


19. REMOVE CYLINDER HEAD COVER LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.

  1. Remove the ventilation valve from the cylinder head cover.


20. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE
  1. Disconnect the 2 oil control valve connectors.

  1. Remove the 2 bolts and 2 oil control valves.


21. REMOVE VVT SENSOR

  1. A076414
    Disconnect the No. 4 and No.5 water by-pass hoses.

  1. Disconnect the sensor connector.

  1. G038106
    Remove the bolt and sensor.


22. REMOVE OIL FILTER BRACKET
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.


23. REMOVE TIMING CHAIN COVER

  1. G038101E02
    Remove the 24 bolts and 2 nuts.

  1. G038102E01
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.


24. REMOVE TIMING CHAIN COVER OIL SEAL
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump body. Tape the screwdriver before use..

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →