2014 Hilux · Service Manual BRAKE

C1437 Lost Communication with ECM

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.
DTC Code
DTC Detection Condition
Trouble Area
C1437
When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more.
  1. CAN communication system (Skid control ECU to ECM)
  2. Skid control ECU (Brake actuator assembly)

INSPECTION PROCEDURE

NOTICE:
After replacing the brake actuator assembly, perform calibration (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    EFI Communication Open
    ECM communication open circuit detection / Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the ECUs or disconnecting a connector.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC C1437 is not output
    A
    DTC C1437 is output
    for LHD
    B
    for RHD
    C
    CAN communication system DTC is output
    D



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - ECM)
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU (brake actuator assembly) and ECM (Click here).

  1. Confirm that there is no momentary interruption.


NEXT


4. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC C1437 is not output
    A
    DTC C1437 is output
    for LHD
    B
    for RHD
    C
    CAN communication system DTC is output
    D



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

END


← C1436 Yaw Rate Sensor Malfunction (from Aug 2014)C1437 Lost Communication with ECM (Aug 2012 – Jul 2013) →