2014 Hilux · Service Manual DRIVE LINE

REPLACEMENT

Removal / installation · Vehicles built from Jun 2011


1. DRAIN DIFFERENTIAL OIL

  1. for front differential:

    1. Stop the vehicle on a level surface.

    2. A272242E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }

  1. for rear differential:

    1. Stop the vehicle on a level surface.

    2. Remove the differential filler plug and gasket.

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


2. REMOVE REAR PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)


3. REMOVE REAR DRIVE PINION NUT

  1. C236628E01
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

  1. C236629E01
    Using SST to hold the companion flange in place, remove the nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C238724
    Using SST, remove the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C236631E01
    Using SST, remove the oil seal.
    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger


6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Remove the oil slinger from the drive pinion.


7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C236632E01
    Using SST, remove the roller bearing (inner).
    SST
    09556-22010  

  1. C236633E01
    Using SST, tap out the roller bearing (outer).
    SST
    09308-00010  


8. REMOVE DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.


9. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C237515
    Remove the bearing spacer from the drive pinion.


10. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C237515
    Install a new bearing spacer.

    HINT:
    Make sure the spacer is installed correctly.


11. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.


12. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C237516E01
    Using SST and a hammer, tap in the roller bearing (outer).
    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).


13. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Install the oil slinger to the drive pinion.


14. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C236636E01
    Using SST and a hammer, tap in a new oil seal.
    SST
    09554-30011  
    Text in Illustration 
    *a
    Oil Seal Depth

    Standard oil seal depth:
    0 +/-0.3mm (0 +/-0.0118in.)

  1. Apply MP grease to the lip of the oil seal.


15. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C238725
    Using SST, install the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.

  1. C237316E01
    Using SST to hold the companion flange in place, install a new nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less


16. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C236639
    Using a torque wrench, measure the preload.

    Standard Preload (Starting Torque):
    Item
    Specified Condition
    New bearing
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf)
    Reused bearing
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf)

    1. If the result is not as specified, adjust the preload.


17. INSPECT TOTAL PRELOAD

  1. C236639
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Total Preload:
    Bearing
    Specified Condition
    New bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    If the result is not as specified, adjust the preload.


18. STAKE DRIVE PINION NUT

  1. C236640
    Using a chisel and hammer, stake the nut.


19. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)


20. ADD DIFFERENTIAL OIL

  1. D025304E51
    Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. for front differential:

    1. A272243E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

← COMPONENTS (from Jun 2011)COMPONENTS (from Jun 2011) →