2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE ENGINE UNDER COVER

3. REMOVE NO. 1 ENGINE UNDER COVER

4. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

G034583E01
  1. Remove the 4 nuts, 4 bolts and frame crossmember.


5. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).


6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Remove the propeller with center bearing shaft assembly (Click here).


7. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }


8. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C118024
  1. Remove the oil dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.


9. DISCONNECT OIL COOLER TUBE

C118031
  1. Using a union nut wrench, disconnect the tube outlet and tube inlet.

  1. C118032
    Remove the 3 bolts and 3 clamps.


10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.


11. REMOVE STARTER ASSEMBLY
  1. for 1.4 kW Type:
    Remove the starter (Click here).

  1. for 1.6 kW Type:
    Remove the starter (Click here).


12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

G034520E01
  1. Support the transmission with a transmission jack.


13. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

  1. C238044
    Detach the wire harness clamp from the No. 3 frame crossmember.

  1. G034517
    Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.


14. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

C238609
  1. Remove the 4 bolts, ground cable and engine mounting insulator.


15. DISCONNECT CONNECTOR

  1. C240769
    Remove the 2 bolts and heat insulator.

  1. G034521E01
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the park/neutral position switch connector, transmission wire connector, ATF temperature sensor connector and 3 speed sensor connectors.

  1. Disconnect the 4 wire harness clamps.


16. REMOVE FLYWHEEL HOUSING DUST SEAL
  1. Remove the flywheel housing dust seal.


17. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

  1. C118033
    Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch mounting bolts.

  1. C118034
    Remove the 3 bolts and exhaust manifold stay.

  1. C118035
    Remove the 7 bolts.

  1. Separate the transmission from the engine.


18. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Remove the torque converter from the automatic transmission assembly.


19. REMOVE TRANSMISSION CONTROL CABLE BRACKET

  1. G024484E01
    Remove the 2 bolts and control cable bracket from the transmission.

← REMOVAL (Jun 2011 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →