2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

B277221
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.


3. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B278222
  1. Detach the 4 claws and remove the parking brake hole cover.


4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Detach the 12 claws and remove the upper console panel.

    NOTICE:
    Be careful not to damage the instrument panel and console box with the claws of the upper console panel.


    B277548E01
    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


5. REMOVE CONSOLE BOX ASSEMBLY

B278048E01
  1. Remove the 4 screws and 2 bolts.

  1. Using a clip remover, remove the 2 clips and console box.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


6. REMOVE SHIFT LEVER BOOT ASSEMBLY

  1. C239519
    Remove the 4 screws and shift lever boot.


7. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY
  1. Fold back the transfer front drive shift boot.

  1. C213734
    Using needle-nose pliers, remove the snap ring and pull out the shift lever.

    HINT:
    Move the transfer shift lever to the H4 position.


8. REMOVE NO. 1 ENGINE UNDER COVER

9. REMOVE NO. 2 ENGINE UNDER COVER

10. REMOVE NO. 3 ENGINE UNDER COVER

11. DISCONNECT HEATED OXYGEN SENSOR
  1. Disconnect the 2 sensor connectors.


12. REMOVE EXHAUST PIPE
  1. Remove the exhaust pipe assembly (Click here).


13. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    Remove the front propeller shaft assembly (Click here).

  1. for TMT Made:
    Remove the front propeller shaft assembly (Click here).


14. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. for TSAM Made:
    Remove the propeller shaft with center bearing assembly (Click here).

  1. for TMT Made:
    Remove the propeller shaft with center bearing assembly (Click here).


15. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


16. REMOVE MANIFOLD STAY

F050360E01
  1. Remove the 3 bolts and manifold stay.


17. REMOVE NO. 2 MANIFOLD STAY

F050356E01
  1. Remove the 3 bolts and manifold stay.


18. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Remove the 6 nuts, exhaust manifold and gasket.


19. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Remove the 6 nuts, exhaust manifold and gasket.


20. DISCONNECT OIL COOLER TUBE

  1. C111240
    Using a union nut wrench, disconnect the outlet tube and inlet oil cooler tube.

  1. C244708
    Remove the 2 bolts and 2 clamps.


21. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C111231
    Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.


22. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

  1. C111232
    Remove the 2 bolts and control cable bracket from the transmission.


23. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

  1. C111233
    Support the transmission with a transmission jack.


24. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

  1. G034256E02
    Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.


25. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

G034260E01
  1. Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.


26. DISCONNECT WIRE HARNESS

  1. C214940
    Remove the nut and disconnect the ground cable.

  1. C112845
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the No. 1 indicator switch connector.

  1. Disconnect the No. 2 indicator switch connector.

  1. Disconnect the No. 3 indicator switch connector.

  1. Disconnect the speed sensor connector.

  1. Detach the 7 wire harness clamps.


27. REMOVE STARTER ASSEMBLY
  1. for 1.4 kW Type:
    Remove the starter assembly (Click here).

  1. for 1.6 kW Type:
    Remove the starter assembly (Click here).


28. REMOVE FLYWHEEL HOUSING SIDE COVER

F050352E01
  1. Remove the flywheel housing side cover from the cylinder block.


29. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

  1. C111234
    Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch setting bolts.

  1. C111235
    Remove the 9 bolts.

  1. Remove the automatic transmission assembly.


30. REMOVE TRANSFER ASSEMBLY
  1. Remove the transfer assembly (Click here).


31. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Remove the torque converter clutch assembly from the automatic transmission assembly.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →