2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

4. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A112147E01


5. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

6. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o Intercooler)

A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the pipe together with the 2 air hoses.


7. REMOVE RADIATOR HOSE INLET

8. REMOVE FAN SHROUD

  1. A110387
    Remove the 3 bolts and oil reservoir.

  1. A252176
    Disconnect the No. 1 and No. 2 water by-pass hoses from the radiator.

  1. Remove the 2 bolts and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling with fan.

  1. Remove the fan and generator V belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling with fan, and then remove the fan shroud together with the fluid coupling with fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump.


9. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


10. REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

  1. I034100E02
    Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.


11. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
  1. Remove the 4 bolts and No. 1 viscous heater bracket.


12. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


13. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.


14. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A098937E01
    Remove the 4 bolts and V-ribbed belt tensioner.


15. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ Intercooler)

  1. A111790
    Disconnect the 2 connectors.

  1. A111832
    Remove the 2 bolts, 2 nuts, throttle body and gasket.


16. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. w/ Intercooler:

    1. A211871
      Remove the 2 nuts and No. 3 injection pipe clamp.

    2. A211872
      Remove the 2 bolts and 2 No. 2 injection pipe clamps.

    3. A272112E01
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A231803E02
      Remove the bolt and No. 2 injection pipe clamp.
      Text in Illustration 
      *1
      No. 2 Injection Pipe Clamp
      *2
      No. 3 Injection Pipe Clamp
      *a
      Injector Side
      *b
      Common Rail Side

    2. Remove the 2 nuts and No. 3 injection pipe clamp.

    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


17. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ Intercooler)

  1. A273018E01
    Remove the 3 bolts and No. 2 intake air connector bracket.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler
    *1
    No. 2 Intake Air Connector Bracket
    *2
    Intake Air Connector


18. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ Intercooler)

  1. A147216
    Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.


19. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ Intercooler)

  1. w/ Intercooler:

    1. A211846
      Disconnect the 2 connectors.

    2. A252294
      Disconnect the 6 vacuum hoses.

    3. Remove the bolt and No. 1 gas filter with gas filter bracket.

    4. A211848
      Remove the 2 bolts and electric vacuum regulating valve.

  1. w/o Intercooler:

    1. A212373
      Disconnect the connector.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.


20. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147230
    Remove the 3 nuts, No. 2 intake air connector and gasket.


21. REMOVE INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147219
    Remove the 3 bolts, intake air connector and 2 gaskets.


22. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A211879
    Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.


23. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. w/ Intercooler:

    1. A152275
      Remove the bolt and disconnect the injection pipe clamp.

    2. A152276E07
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A098893E01
      Remove the 2 bolts and disconnect the 2 injection pipe clamps.

    2. A231804E02
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side


24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. Remove the 3 bolts and disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


25. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. A148169
    Remove the 6 bolts and timing belt cover.


26. REMOVE TIMING BELT

  1. A070549E02
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

  1. A070550E01
    Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.


27. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of the camshaft timing pulley.

  1. Remove the camshaft timing pulley.


28. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and No. 2 timing belt cover.


29. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A252180
    Remove the 5 bolts, 2 nuts, engine water pump and gasket.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →