2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.


2. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

4. REMOVE ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A112147E01


5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ No. 1 Engine Cover)

  1. w/ No. 1 Engine Cover

    1. A099256E03
      Detach the 4 claws from the pins of the engine cover bracket and remove the No. 1 engine cover sub-assembly.
      Text in Illustration 
      *1
      No. 1 Engine Cover Sub-assembly
      *2
      Claw
      *3
      Pin

    2. Remove the 2 bolts and engine cover bracket.

  1. A111789
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe sub-assembly together with the 2 air hoses.


6. REMOVE VENTILATION HOSE HEAT INSULATOR (w/o Intercooler)
  1. Remove the 2 bolts and ventilation hose heat insulator.


7. REMOVE AIR CLEANER ASSEMBLY

  1. w/ Mass Air Flow Meter:

    1. Disconnect the mass air flow meter connector and detach the wire harness clamp.

      A311928E01

      Text in Illustration 
      *A
      w/ Intercooler
      *B
      w/o Intercooler

    2. Loosen the hose clamp, and then remove the No. 1 air cleaner hose from the turbocharger sub-assembly.

    3. w/o Intercooler:
      Slide the clamp and disconnect the ventilation hose from the cylinder head cover sub-assembly.

    4. Remove the 2 bolts and air cleaner assembly.

  1. w/o Mass Air Flow Meter:

    1. A311929
      Detach the clamp and disconnect the intake air temperature sensor connector.

    2. Loosen the hose clamp, and then remove the air cleaner hose from the turbocharger sub-assembly.

    3. Slide the clamp and disconnect the ventilation hose from the cylinder head cover sub-assembly.

    4. Remove the 2 bolts and air cleaner assembly.


8. REMOVE VENTILATION PIPE (w/ Intercooler)

  1. A288742
    for Type A:
    Slide the 2 clamps and disconnect the No. 12 water by-pass hose and No. 13 water by-pass hose from the ventilation pipe.

  1. A288747E02
    Remove the bolt and ventilation pipe.
    Text in Illustration 
    *A
    for Type B
    *B
    for Type A


9. REMOVE COMPRESSOR INLET ELBOW (w/ Intercooler)

  1. A288737
    Disconnect the 2 connectors and detach the wire harness clamp.

  1. for Type A:

    1. A291249
      Slide the clamp and disconnect the No. 1 turbo water hose from the cylinder block sub-assembly.

    2. A288735E02
      Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 13 water by-pass hose from the No. 2 water by-pass pipe sub-assembly and compressor inlet elbow.
      Text in Illustration 
      *1
      No. 2 Water By-pass Hose
      *2
      No. 13 Water By-pass Hose

  1. Remove the 2 nuts, compressor inlet elbow and gasket.

  1. A288733E01
    for Type A:
    Slide the 2 clamps and remove the No. 7 water by-pass hose and No. 12 water by-pass hose from the compressor inlet elbow.
    Text in Illustration 
    *1
    No. 7 Water By-pass Hose
    *2
    No. 12 Water By-pass Hose

  1. A211835
    for Type B:
    Slide the 4 clamps and disconnect the 2 No. 1 turbo water hoses from the No. 1 turbo water pipe sub-assembly and cylinder block sub-assembly.


10. DISCONNECT NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP (for Automatic Transmission)

A097634E01
  1. Remove the bolt and disconnect the No. 1 automatic transmission oil cooler tube clamp.


11. DISCONNECT RADIATOR HOSE OUTLET
  1. Disconnect the radiator hose outlet from the water inlet.


12. REMOVE WATER INLET

A097637E01
  1. Remove the 3 bolts and water inlet.


13. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →