2014 Hilux · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

The navigation receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM

C240170E46

INSPECTION PROCEDURE


1. CHECK SPEAKER (OPERATION CHECK)

  1. E273721
    Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check (Click here).

  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area (for Double Cab)
    B
    Malfunction in rear speaker area (for Extra Cab)
    C



B
Go to step 7

C
Go to step 9
A


2. CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappear
    B



B
Go to step 4
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the N12 navigation receiver assembly connector.

  1. Disconnect the T24*1 and/or T23*2 front No. 2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N12-1 (FR+) - T24-4
    Always
    Below 1 Ω
    N12-5 (FR-) - T24-2
    N12-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    N12-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N12-2 (FL+) - T23-4
    Always
    Below 1 Ω
    N12-6 (FL-) - T23-2
    N12-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    N12-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the front No. 1 speaker assembly connector.

  1. Inspect the front No. 1 speaker assembly connector (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T24*1 and/or T23*2 front No. 2 speaker assembly connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 - S16-1
    Always
    Below 1 Ω
    T24-1 - S16-2
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T23-3 - S15-1
    Always
    Below 1 Ω
    T23-1 - S15-2
    T23-3 - Body ground
    Always
    10 kΩ or higher
    T23-1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

7. INSPECT REAR SPEAKER ASSEMBLY
  1. Disconnect the rear speaker assembly connector.

  1. Inspect the rear speaker assembly connector (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. Disconnect the N11 navigation receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N11-1 (RR+) - S18-1
    Always
    Below 1 Ω
    N11-3 (RR-) - S18-2
    N11-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    N11-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N11-2 (RL+) - S17-1
    Always
    Below 1 Ω
    N11-6 (RL-) - S17-2
    N11-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    N11-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

9. INSPECT REAR SPEAKER ASSEMBLY
  1. Disconnect the rear speaker assembly connector.

  1. Inspect the rear speaker assembly connector (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. Disconnect the N11 navigation receiver assembly connector.

  1. Disconnect the S20*1 and/or S19*2 rear speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N11-1 (RR+) - S20-1
    Always
    Below 1 Ω
    N11-3 (RR-) - S20-2
    N11-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    N11-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N11-2 (RL+) - S19-1
    Always
    Below 1 Ω
    N11-6 (RL-) - S19-2
    N11-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    N11-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)


← Parking Brake Switch Circuit (from Aug 2013)Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter (from Aug 2013) →