2014 Hilux · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Lines for Short Circuit

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Brake actuator assembly (skid control ECU)
  3. Spiral cable (steering angle sensor)
  4. Yaw rate sensor
  5. ECM
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM

C245036E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

  1. C245024E01
    Disconnect the J49 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J49-2 (CANH) - D1-6 (CANH)
    Ignition switch off
    Below 1 Ω
    J49-1 (CANL) - D1-14 (CANL)
    Ignition switch off
    Below 1 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the J49 No. 3 junction connector.


NEXT


4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. H102621E28
    Disconnect the J54 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 11
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C190787E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J54-13 (CANH) - J54-7 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 7
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C190787E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J54-12 (CANH) - J54-6 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 9
OK

REPLACE NO. 1 JUNCTION CONNECTOR

7. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


8. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. C190680E08
    Disconnect the S35 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-25 (CANH) - S35-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

9. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


10. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. for 1KD-FTV, 2KD-FTV (w/ DPF):

    1. C245028E01
      Disconnect the E30 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E30-35 (CANH) - E30-36 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. for 1KD-FTV, 2KD-FTV (w/o DPF):

    1. C190783E03
      Disconnect the E6 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E6-24 (CANH) - E6-23 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. for 1GR-FE:

    1. C245027E01
      Disconnect the E13 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E13-33 (CANH) - E13-34 (CANL)
      Ignition switch off
      108 to 132 Ω

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2KD-FTV)
B
OK (for 1GR-FE)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

11. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


12. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C245025E02
    Disconnect the J59 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J59-5 (CANH) - J59-16 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


13. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

  1. H102621E28
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 17
OK


14. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)

  1. C245025E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J59-7 (CANH) - J59-18 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 15
OK

REPLACE NO. 2 JUNCTION CONNECTOR

15. CONNECT CONNECTOR
  1. Reconnect the J59 No. 2 junction connector.


NEXT


16. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR)

  1. C190781E08
    Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR (Click here)

17. CONNECT CONNECTOR
  1. Reconnect the J59 No. 2 junction connector.


NEXT


18. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C190789E06
    Disconnect the J50 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J50-2 (CANH) - J50-1 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C190789E07
    Disconnect the J51 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J51-2 (CANH) - J51-1 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 20
OK

REPLACE NO. 3 JUNCTION CONNECTOR

20. CONNECT CONNECTOR
  1. Reconnect the J50 and J51 No. 3 junction connectors.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

  1. C190782E08
    Disconnect the S37 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S37-4 (CANH) - S37-3 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (Click here)


← Check CAN Bus Lines for Short Circuit (Jun 2011 – Jul 2012)Check CAN Bus Lines for Short Circuit (Aug 2013 – Jul 2014) →