Check CAN Bus Line for Short to +B
Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.| Symptom |
Trouble Area |
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 2. CHECK FOR SHORT TO +B IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
Disconnect the J49 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
D1-6 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
D1-14 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 3. CONNECT CONNECTOR |
Reconnect the J49 No. 3 junction connector.
| NEXT | |
| 4. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE) |
Disconnect the J54 No. 1 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
D1-6 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
D1-14 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J54-13 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J54-7 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J54-12 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J54-6 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 7. CONNECT CONNECTOR |
Reconnect the J54 No. 1 junction connector.
| NEXT | |
| 8. CHECK FOR SHORT TO +B IN CAN BUS WIRE (SKID CONTROL ECU) |
Disconnect the S35 skid control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
S35-25 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
S35-14 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CONNECT CONNECTOR |
Reconnect the J54 No. 1 junction connector.
| NEXT | |
| 10. CHECK FOR SHORT TO +B IN CAN BUS WIRE (ECM) |
for 1KD-FTV, 2KD-FTV (w/ DPF):

Disconnect the E30 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
E30-35 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
E30-36 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
for 1KD-FTV, 2KD-FTV (w/o DPF):

Disconnect the E6 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
E6-24 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
E6-23 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
for 1GR-FE:

Disconnect the E13 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
E13-33 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
E13-34 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
| Result |
Proceed to |
| OK (for 1KD-FTV) |
A |
| OK (for 2KD-FTV) |
B |
| OK (for 1GR-FE) |
C |
| NG |
D |
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CONNECT CONNECTOR |
Reconnect the J54 No. 1 junction connector.
| NEXT | |
| 12. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
Disconnect the J59 No. 2 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J59-5 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J59-16 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 13. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
D1-6 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
D1-14 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 14. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J59-7 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J59-18 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 15. CONNECT CONNECTOR |
Reconnect the J59 No. 2 junction connector.
| NEXT | |
| 16. CHECK FOR SHORT TO +B IN CAN BUS WIRE (YAW RATE SENSOR) |
Disconnect the Y1 yaw rate sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
Y1-3 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
Y1-2 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 17. CONNECT CONNECTOR |
Reconnect the J59 No. 2 junction connector.
| NEXT | |
| 18. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Disconnect the J50 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J50-2 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J50-1 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 19. CHECK FOR SHORT TO +B IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
Disconnect the J51 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
J51-2 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
J51-1 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 20. CONNECT CONNECTOR |
Reconnect the J50 and J51 No. 3 junction connectors.
| NEXT | |
| 21. CHECK FOR SHORT TO +B IN CAN BUS WIRE (STEERING ANGLE SENSOR) |
Disconnect the S37 steering angle sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Measured Resistance
S37-4 (CANH) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
S37-3 (CANL) - D1-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
